Bosch NWD-495V03-20P Operating Instructions - Page 28

Closing the unit

Get Bosch NWD-495V03-20P PDF manuals and user guides View all Bosch NWD-495V03-20P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

28 en | Camera set-up FlexiDomeDN IP i 4.3.2 i 4.4 NOTICE! The new IP address, subnet mask and gateway address are set after you leave the menu. The camera reboots internally and the new values are set after a few seconds. Defaults To restore all parameters (including IP address) to the factory defaults, press and hold the Up navigation key for at least 10 seconds and then confirm. Allow a few seconds for the camera to optimize the picture after a mode reset. NOTICE! Restoring the factory defaults may result in the loss of the IP connection. If this occurs, change the IP address of your browser to the factory default value. Only restore the factory defaults when it is absolutely necessary. Closing the unit When the camera position is set and all adjustments have been made, close the unit. 1. Remove the monitoring jack. 2. Place the inner liner in position aligning its fin with the bracket on the base. 3. Place the dome onto the base and rotate until it clips into place. (If necessary clean its surface with a soft cloth.) 4. Place the sealing ring and the trim ring over the dome. 5. Align the tamper-resistant screws in the trim ring with threaded ends in the mounting base. 6. Use the supplied special screwdriver bit to tighten the three tamper-resistant screws. V 1.0 | 2006.12 Operating Instructions Bosch Security Systems

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
28
en | Camera set-up
FlexiDome
DN
IP
V 1.0 | 2006.12
Operating Instructions
Bosch Security Systems
4.3.2
Defaults
To restore all parameters (including IP address) to the factory
defaults, press and hold the Up navigation key for at least 10
seconds and then confirm. Allow a few seconds for the camera
to optimize the picture after a mode reset.
4.4
Closing the unit
When the camera position is set and all adjustments have been
made, close the unit.
1.
Remove the monitoring jack.
2.
Place the inner liner in position aligning its fin with the
bracket on the base.
3.
Place the dome onto the base and rotate until it clips into
place. (If necessary clean its surface with a soft cloth.)
4.
Place the sealing ring and the trim ring over the dome.
5.
Align the tamper-resistant screws in the trim ring with
threaded ends in the mounting base.
6.
Use the supplied special screwdriver bit to tighten the
three tamper-resistant screws.
i
NOTICE!
The new IP address, subnet mask and gateway address are set
after you leave the menu. The camera reboots internally and the
new values are set after a few seconds.
i
NOTICE!
Restoring the factory defaults may result in the loss of
the IP connection. If this occurs, change the IP address of your
browser to the factory default value. Only restore the factory
defaults when it is absolutely necessary.