Brother International BAS-705 Instruction Manual - English - Page 13

Detal on standard data settings, 2-12. Checking the sewing data, Panel Ver.

Get Brother International BAS-705 PDF manuals and user guides View all Brother International BAS-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

2. PREPARATION 2-11. Detal on standard data settings Main Ver. = 1.0 Panel Ver. = 1.0 X - Y Ver. = 1.0 Set home position 1. Check that the air is being supplied. * Refer to "2-7. Using the air unit" on page 8. 2. Turn on the power switch. 3. Press the START switch. The machine will then the home position for the upper shaft X-Y feed and the lower shaft. Press the start switch AUTO MODE Loop length 1 s t bobbin counter 2nd bobbin counter No loop NOTE: ɾWait for at least 10 seconds after turning off the power before turning it back on again. If you do not wait long enough, the error code "E-330"will appear on the display. ɾIf there is no belt loop in position under the ac tuator, the message shown at left will be displayed. If this happens, refer to "2-10. Passing through the belt loops" on page 9. pass loop through the channel 2-12. Checking the sewing data AUTO MODE Production counter 1 s t bobbin counter 2nd bobbin counter AUTO MODE 1 s t bobbin counter 2nd bobbin counter Speed After the home position has been determined, press the SELECT switches (˛ and ˝). The screen will then start scrolling so that you can check the sewing data settings. AUTO MODE 2nd bobbin counter Speed Loop length ʕ 10 ʕ B A S -705

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
2. PREPARATION
2-11.
Detal on standard data settings
―
10
―
BAS-705
1.
Check that the air is being supplied.
*
Refer to "2-7. Using the air unit" on page 8.
2.
Turn on the power switch.
3.
Press the START switch. The machine will then the
home position for the upper shaft
X-Y feed and the
lower shaft.
NOTE:
・
Wait for at least 10 seconds after turning off
the power before turning it back on again. If
you do
not wait long enough, the error code
"E-330"
will appear on the display.
・
If there is no belt loop in position under the ac
tuator, the message shown at left will be dis-
played.
If this happens, refer to "2-10. Passing through
the belt loops" on page 9.
AUTO MODE
Loop length
1st
bobbin counter
2nd bobbin counter
<BAS - 705 >
Main Ver.
= 1.0
Panel Ver.
= 1.0
X - Y
Ver.
= 1.0
2-12. Checking the sewing data
After the home position has been determined, press
the SELECT switches (
▲
and
▼
). The screen will then
start scrolling so that you can check the sewing data
settings.
Set home position
Press the start switch
No loop
pass loop through the channel
AUTO MODE
2nd bobbin counter
Speed
Loop length
AUTO MODE
1st
bobbin counter
2nd bobbin counter
Speed
AUTO MODE
Production counter
1st
bobbin counter
2nd bobbin counter