Brother International BAS-705 Instruction Manual - English - Page 26

X-Y movement, X-Y/MOVE/ ADJ

Get Brother International BAS-705 PDF manuals and user guides View all Brother International BAS-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

3. PANEL OPERATION 3-2-10. X-Y movement ɾ This procedure lets you set the parallel movement of the pattern in the X feed direction and Y feed direction. ɾ The setting range is from -1 to +1 in both the X direction and Y direction. However, it may not be possible to change the setting within this range because an area check will be carried out when the setting is changed. #"4 WARNING POWER Ϧηοτ RESET Ϟʔυ MODE બ୒ SELECT औΓফ͠ CANCEL r w ֬ ఆ ENTER AUTO MODE ˗ Loop length 1st bobbin counter 2nd bobbin counter ADJUSTMENT(/) Loop/ program ˗ X-Y/ test feed X-Y/ feed X-Y/MOVE/ (ADJ) Program No. ˗Xmove (mmx10) X-Y/MOVE/ (ADJ) Program No. ˗Xmove (mmx10) e t z/ z/ ˛ 1. Press the MODE switch w to select AUTO mode. 2. While pressing the SELECT switch e, press the MODE switch w. * This will change the mode to ADJUSTMENT mode. 3. Use the˛and ˝SELECT switches e to move the pointer "˗" so that "X-Y/program" is selected, and then press the ENTER switch t. 4. Use the ˛ and ˝ SELECT switches e again to move the pointer "˗" so that "X move" or "Y move" is selected. 5. While using the SELECT switch e to move the cursor "-" , press the ˛ and ˝ SELECT switches e to set the amount of movement. * If the CANCEL switch r is pressed, the old previously-set scale ratio will appear again on the display. 6. Press the ENTER switch t. * The new scale ratio setting for the X move or Y move will appear on the display. ˛ ʕ 23 ʕ B A S -705

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
3. PANEL OPERATION
3-2-10. X-Y movement
―
23
―
BAS-705
・
This procedure lets you set the parallel movement of the pattern in the X feed direction
and Y feed direction.
・
The setting range is from -1 to +1 in both the X direction and Y direction. However, it may
not be possible to change the setting within this range because an area check will be
carried out when the setting is changed.
AUTO MODE
◆
Loop length
1st bobbin counter
2nd bobbin counter
ADJUSTMENT(/)
Loop/ program
◆
X-Y/ test feed
X-Y/ feed
1.
Press the MODE switch
w
to select AUTO mode.
2.
While pressing the
SELECT switch
e
, press the
MODE switch
w
.
*
This will change the mode to ADJUSTMENT
mode.
3.
Use the
▲
and
▼
SELECT switches
e
to move the
pointer "
◆
" so that "X-Y/program" is selected, and
then press the ENTER switch
t
.
4.
Use the
▲
and
▼
SELECT switches
e
again to
move the pointer "
◆
" so that "X
move" or "Y move"
is selected.
5. While using the
SELECT switch
e
to move the
cursor "
-
" , press the
▲
and
▼
SELECT switches
e
to set the amount of movement.
*
If the CANCEL switch
r
is pressed, the
old previously-set scale ratio will appear again
on the display.
6.
Press the ENTER switch
t
.
*
The new scale ratio setting for the X
move or Y
move will appear on the display.
▲
X-Y/MOVE/ (ADJ)
Program No.
◆
Xmove (mmx10)
z/
▲
選択�
SELECT
モード�
MODE
確 定�
ENTER
リセット�
RESET
電源�
POWER
取り消し�
CANCEL
警告�
WARNING
BAS-705
r
t
e
w
X-Y/MOVE/ (ADJ)
Program No.
◆
Xmove (mmx10)
z/