Brother International BAS-705 Instruction Manual - English - Page 58

Adjustments required when the belt loop thickness is changed, 3-2. Adjusting loop support T

Get Brother International BAS-705 PDF manuals and user guides View all Brother International BAS-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

6. STANDARD ADJUSTMENT (MECHANISMS) 6-3. Adjustments required when the belt loop thickness is changed ɾ Carry out the following adjustment if the thickness of the belt loops has been changed. 6-3-1. Adjusting joint sensor 1. Turn the power on. Loop sensor Joint sensor 2+0.5mm Actuator e w 2. Loosen the bolt q. 3. Adjust the dimension between the center of the joint sensor and actuator edge to 2 ʶ 0.5 mm using the adjusting shaft w. 2+0.5mm NOTE: Check that the joint sensor detects the belt loop q joint. When the joint sensor detects the belt loop joint, the SEAM JOINT indicator lights. Belt loop 4. Adjust the dimension between the center of the loop sensor and actuator edge to 2 ʶ 0.5 mm using the When belt loop is not present When joint is present bolt e. NOTE1: Check that the loop sensor functions properly when the belt loop is not set. When the loop sensor detects that the belt loop is not set, the LOOP EMPTY indicator lights. NOTE2: If the belt loop is thin, adjust the dimension so that it is smaller than 2 ʶ 0.5 mm. 6-3-2. Adjusting loop support T w 1. If belt loops with no curls are being fed during step operation, adjust so that the clearance between loop support T q and the belt loops is approximately 0.5 mm. 2. Loosen the screw w and move loop support T q in the direction of the arrow to adjust. q belt loops 0.5mm ʕ55ʕ BAS-705

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
6-3-2. Adjusting loop support T
・
Carry out the following adjustment if the thickness of the belt loops has been changed.
6. STANDARD ADJUSTMENT (MECHANISMS)
1.
Turn the power on.
2.
Loosen the bolt
q
.
3.
Adjust the dimension between the center of the joint
sensor and actuator edge to 2
±
0.5 mm using the
adjusting shaft
w
.
NOTE:
Check that the joint sensor detects the belt loop
joint. When the joint sensor detects the belt
loop joint, the SEAM JOINT indicator lights.
4.
Adjust the dimension between the center of the loop
sensor and actuator edge to 2
±
0.5 mm using the
bolt
e
.
NOTE1: Check that the loop sensor functions properly
when the belt loop is not set. When the loop
sensor detects that the belt loop is not set, the
LOOP EMPTY indicator lights.
NOTE2: If the belt loop is thin, adjust the dimension so
that it is smaller than 2
±
0.5 mm.
6-3. Adjustments required when the belt loop thickness is changed
1.
If belt loops with no curls are being fed during step
operation, adjust so that the clearance between loop
support T
q
and the belt loops is approximately 0.5
mm.
2.
Loosen the screw
w
and move loop support T
q
in
the direction of the arrow to adjust.
6-3-1. Adjusting joint sensor
―
55
―
BAS-705
w
q
0.5mm
belt loops
e
w
q
Belt loop
Joint sensor
2+0.5mm
2+0.5mm
Actuator
Loop sensor
When belt loop
is not present
When joint
is present