Brother International BAS-705 Instruction Manual - English - Page 56

Adjusting the loop guide spring, 2-4. During sewing, and retract

Get Brother International BAS-705 PDF manuals and user guides View all Brother International BAS-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

6. STANDARD ADJUSTMENT (MECHANISMS) 6-2-3. Adjusting the loop guide spring e e "0" r t q w 1. Loosen the set screw q. 2. With the air released, move the loop guide spring e to adjust so that the distance A is 0 when the belt loop w is being pressed. 3. After adjusting, tighten the set screw q to secure the loop guide spring e. NOTE ɾCheck that the loop guide spring e does not interfere with the channel of the loop presser r. ɾCheck that the edge of the belt loop is parallel to the edge of the presser foot. If they are at an angle, loosen the bolt t and adjust as necessary. 6-2-4. During sewing [If the horizontal position of the belt loops or the center position of the bar tackings is incorrect] graduation w 1. Loosen the retract clamp lever q and retract the feeder w. q 2. Loosen the nut e. t 3. Turn the bolt r to adjust the transfer position of the r belt loops. 4. After adjusting, tighten the nut e to secure the feeder e w. NOTE: Check that the sensor t illuminates at this time. ʕ53ʕ B A S -705

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
6. STANDARD ADJUSTMENT (MECHANISMS)
6-2-3. Adjusting the loop guide spring
1.
Loosen the set screw
q
.
2.
With the air released, move the loop guide spring
e
to adjust so that the distance A is 0 when the belt
loop
w
is being pressed.
3.
After adjusting, tighten the set screw
q
to secure
the loop guide spring
e
.
NOTE
・
Check that the loop guide spring
e
does not
interfere with the channel of the loop presser
r
.
・
Check that the edge of the belt loop is parallel
to the edge of the presser foot.
If they are at an angle, loosen the bolt
t
and
adjust as necessary.
6-2-4. During sewing
―
53
―
BAS-705
[If the horizontal position of the belt loops or the center
position of the bar tackings is incorrect]
q
r
e
w
t
graduation
1.
Loosen the retract clamp lever
q
and retract the
feeder
w
.
2.
Loosen the nut
e
.
3.
Turn the bolt
r
to adjust the transfer position of the
belt loops.
4.
After adjusting, tighten the nut
e
to secure the feeder
w
.
NOTE:
Check that the sensor
t
illuminates at this
time.
t
w
q
r
e
e
"0"