Brother International BAS-705 Instruction Manual - English - Page 55

Adjustments required when the belt loop width is changed, 2-1. Adjusting channel

Get Brother International BAS-705 PDF manuals and user guides View all Brother International BAS-705 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

6. STANDARD ADJUSTMENT (MECHANISMS) 6-2. Adjustments required when the belt loop width is changed 6-2-1. Adjusting channel e w r q belt loop coupler center line center line 9mm from center line 10mm from center line 8mm from center line 7mm from center line 6mm from center line 5mm from center line 1. Loosen the two bolts q up to 7 mm, and remove the channel assembly from the unit. NOTE: Fine adjustment of channel B (left side) w should be carried out while the channel as sembly is attached. 2. Loosen the four screws e and align the channel to the width of the belt loop. (Example) How to align if the belt loop width is 14 mm (a) Align the perpendicular surface of channel F (right side) r with a line 7 mm from the cente line. (b) Set the position of channel B (left side) w so that the belt loop joints pass through smoothly. NOTE: If the center of the V cut is misaligned, move channel F (right side) r horizontally. 3. Position the coupler of the channel to the coupler of the unit base. Secure them using the bolt q. w r 6-2-2. Adjusting the width adjustment plate e r loop width adjustment plate t 1. With loop presser B q and loop presser F w both in the raised position, loosen the clamp lever e. 2. Turn the bolt r so that the left edge of channel F t is aligned with the edges of loop presser B q and loop presser F w. 3. Tighten the clamp lever e. NOTE: If the belt loops run along the right edge of channel B, align the edges of loop presser B q and loop presser F w the end of the belt loops. q w ʕ52ʕ B A S -705

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
6-2. Adjustments required when the belt loop width is changed
6-2-1. Adjusting channel
1.
Loosen the two bolts
q
up to 7 mm, and remove the
channel assembly from the unit.
NOTE:
Fine adjustment of channel B (left side)
w
should be carried out while the channel as
sembly is attached.
2.
Loosen the four screws
e
and align the channel to
the width of the belt loop.
(Example)
How to align if the belt loop width is 14 mm
(a)
Align the perpendicular surface of channel F
(right side)
r
with a line 7 mm from the cente
line.
(b)
Set the position of channel B (left side)
w
so
that the belt loop joints pass through smoothly.
NOTE:
If the center of the V cut is misaligned, move
channel F (right side)
r
horizontally.
3.
Position the coupler of the channel to the coupler of
the unit base. Secure them using the bolt
q
.
6. STANDARD ADJUSTMENT (MECHANISMS)
1.
With loop presser B
q
and loop presser F
w
both in
the raised position, loosen the clamp lever
e
.
2.
Turn the bolt
r
so that the left edge of channel F
t
is aligned with the edges of loop presser B
q
and
loop presser F
w
.
3.
Tighten the clamp lever
e
.
NOTE:
If the belt loops run along the right edge of
channel B, align the edges of loop presser
B
q
and loop presser F
w
the end of the
belt loops.
6-2-2. Adjusting the width adjustment plate
―
52
―
BAS-705
t
q
w
e
w
r
q
belt loop
coupler
w
r
center line
center line
9mm from center line
10mm from center line
8mm from center line
7mm from center line
6mm from center line
5mm from center line
r
e
loop width
adjustment plate