Home » Brother International Manuals » Sewing Machines » Brother International BAS-705 » Manual Viewer

Brother International BAS-705 Instruction Manual - English - Page 76

Press the RESET switch., Malfunction of upper shaft motor

Get Brother International BAS-705 PDF manuals and user guides

View all Brother International BAS-705 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

9. ERROR CODES Error code E-302 E-320 E-323 E-324 E-325 E-330 Problem Solution Errors reading to and writing from EEPROM on main circuit board Synchronizati error Upper shaft sensor detection error q Turn off power switch. - w Wait 10 seconds or more, and then turn the power back on again. q Upper shaft motor and lower shaft motor synchronizati error w Open the second bar tacking lower shaft unit and clean away the thread scraps, etc. e Press the RESET switch. q Check the operation of the upper shaft sensor and the upper shaft lock. w Turn off power switch. Start position error Press the RESET switch to determine the home position. Incorrect upper shaft installation q Turn off power switch. position w Check the installation position of the upper shaft. Malfunction of upper shaft motor q Turn off power switch. or lower shaft motor, or tripped w Wait 15 seconds, and then torn the power back on. driver e Check the connection of the servo motor connector. ʕ 73 ʕ B A S -705

Section	Page
Go to Instruction Manual Top Page	1
1. PART NAMES AND SPECIFICATIONS	4
1-1. Part names	4
1-2. Specifications	4
1-3.Program list	5
2. PREPARATION	6
2-1. Installing the machine	6
2-2.Removing the machine head fixing bolt	7
2-3.Removing the BM support slide shaft fixing screw	7
2-4.Installing the auxiliary legs	8
2-5. Checking the loop cutting	8
2-6. Lubrication	9
2-7.Installing the cotton stand	10
2-8.Using the air unit	11
2-9.Pulley rotation direction	11
2-10. Threading belt loop	12
2-11. Detal on standard data settings	13
2-12. Checking the sewing data	13
2-13. Initializing the sewing data	14
3. PANEL OPERATION	15
3-1. Explanation of panel	15
3-2.Data setting methods	16
4. SEWING	27
4-1. Replacing needle	27
4-2. Threading the upper thread	28
4-3 Winding bobbin thread	29
4-4. Replacing the bobbin case and threading the thread	30
4-5. Sewing conditions and thread tension	31
4-6. Trial sewing	33
4-7. Automatic sewing	35
5. STANDARD ADJUSTMENT（MACHINE HEAD）	38
5-1. Tilting back the machine head	38
5-2. Adjusting the needle bar height	39
5-3. Needle bar lift stroke adjustment	40
5-4. Shuttle driver needle contact adjustment	41
5-5. Needle to shuttle hook point gap adjustment	42
5-6. Adjusting the shuttle hook thread guide	43
5-7. Adjusting the movable knife	43
5-8. Adjusting the thread wiper	48
5-9. Adjusting the width between the needles	49
6. STANDARD ADJUSTMENT (MECHANISMS)	51
6-1. Adjustments required when the belt loop length is changed	52
6-2. Adjustments required when the belt loop width is changed	55
6-3. Adjustments required when the belt loop thickness is changed	58
6-4. Adjusting the looseness of the belt loops	64
6-5. Adjusting the folding margin	65
6-6. Adjusting the folding	66
6-7. Changing the loop cutting shape (V cut or flat cut)	67
6-8. Replacing the movable knife and fixed knife	68
6-9. Adjusting the belt loop and presser foot height	68
7. MAINTENANCE AND INSPECTION	69
7-1.Cleaning the rotary hook	69
7-2.Lubrication	69
7-3.Draining the oil	70
7-4.Cleaning the eye guard	70
7-5.Checking the needle	70
7-6.Cleaning the machine pulley	70
8. DIP SWITCH	71
8-1.Panel DIP switch functions	71
8-2.Main circuit board DIP switch functions	73
9. ERROR CODES	74
10. TROUBLESHOOTING	77
10-1. Machine Head	77
10-2. Mechanisms	82
11. OPTIONS	85
11-1. Hand set switch unit	85
11-2. Upper thread breakage detector assembly	86
11-3. Belt loop slackener	87
11-4. Loop setting sensor	88