Brother International FAX-170 Service Manual - Page 69
cutter, sensor, remove, screw.
 |
View all Brother International FAX-170 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 69 highlights
(8) To take out the cutter HP sensor, remove the screw. O (I ((a Drive unit Cutter HP sensor ■ Reassembling Notes • When installing the motor bracket, fit the two holes "a" over the positioning bosses provided on the drive unit. • Make sure that the locking arm clamps the motor. • When installing the drive unit to the scanner frame ASSY, hold the resin part of the drive unit, taking care not to grip the solenoid spring. Fully turn the cutter flange clockwise and turn the upper blade to the angle shown below, and then fit the boss of the cutter flange into the hole of the upper blade. Drive unit Solenoid spring (Do not grip here.) O "a" Boss of cutter flange IV - 20 Upper blade
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64 -
65 -
66 -
67 -
68 -
69 -
70 -
71 -
72 -
73 -
74 -
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
 |
 |
(8)
To
take
out
the
cutter
HP
sensor,
remove
the
screw.
O
Drive
unit
(I
((a
Cutter
HP
sensor
■
Reassembling
Notes
•
When
installing
the
motor
bracket,
fit
the
two
holes
"a"
over
the
positioning
bosses
pro-
vided
on
the
drive
unit.
•
Make
sure
that
the
locking
arm
clamps
the
motor.
•
When
installing
the
drive
unit
to
the
scanner
frame
ASSY,
hold
the
resin
part
of
the
drive
unit,
taking
care
not
to
grip
the
solenoid
spring.
Fully
turn
the
cutter
flange
clockwise
and
turn
the
upper
blade
to
the
angle
shown
below,
and
then
fit
the
boss
of
the
cutter
flange
into
the
hole
of
the
upper
blade.
Drive
unit
Solenoid
spring
(Do
not
grip
here.)
O
"a"
Boss
of
cutter
flange
IV
—
20
Upper
blade