Home » Brother International Manuals » Printers » Brother International HL-3070CW » Manual Viewer

Brother International HL-3070CW Quick Setup Guide - English - Page 14

The installation is now, complete.

UPC - 012502622345

View all Brother International HL-3070CW manuals

Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

USB h The Brother software will search for the Brother printer. During this time the following screen will appear. i Choose the printer you wish to connect, and then click OK. Macintosh j When this screen appears, click OK. Finish The installation is now complete. 14

Section	Page
Quick Setup Guide HL-3070CW	1
Start Here	1
1 Unpack the printer and check the components	1
Symbols used in this guide	3
2 Remove the packing material from the printer	4
3 Install the drum unit and toner cartridge assemblies	4
4 Load paper in the paper tray	5
5 Print a test page	6
6 Set your language on the control panel	7
7 Choose your connection type	9
For USB Interface Cable Users (For Windows® users)	10
8 Install the printer driver and connect the printer to your computer	10
For USB Interface Cable Users (For Mac OS X users)	13
8 Connect the printer to your Macintosh and install the driver	13
For Wired Network Interface Cable Users (For Windows® users)	15
8 For Peer-to-Peer network printer users	15
8 For shared network printer users	18
For Wired Network Interface Cable Users (For Mac OS X users)	20
8 Connect the printer to your Macintosh and install the driver	20
For Wireless Network Interface Users	22
8 Before you begin	22
9 Confirm your network environment (Infrastructure Mode)	23
Configuration using the Brother automatic installer application on the CD-ROM (Recommended)	23
Configuration using the SES/WPS/AOSS from the control panel menu to configure your printer for a wireless network	23
Configuration using the PIN Method of Wi-Fi Protected Setup	23
If your wireless access point a supports Wi-Fi Protected Setup, you can also configure using the PIN Method of Wi-Fi Protected Setup. For instructions, see Chapter 7 in the Network User’s Guide on the CD-ROM.	23
Configuration in Infrastructure mode, using a network cable temporarily (For Windows® users)	24
10 Configure the wireless settings (For Windows® users)	24
Configuration in the Infrastructure mode using SES/WPS or AOSS from the control panel menu (For Windows® users)	30
10 Configure the wireless settings (For Windows® users)	30
Configuration in Infrastructure mode, using a network cable temporarily (For Mac OS X users)	34
10 Configure the wireless settings (For Mac OS X users)	34
Configuration in the Infrastructure mode using SES/WPS or AOSS from the control panel menu (For Mac OS X users)	39
10 Configure the wireless settings (For Mac OS X users)	39
For Network Users	42
BRAdmin Light utility (For Windows® users)	42
Install the BRAdmin Light configuration utility	42
Set your IP Address, Subnet Mask and Gateway using BRAdmin Light	42
BRAdmin Light utility (For Mac OS X users)	43
Set your IP Address, Subnet Mask and Gateway using BRAdmin Light	43
Web Based Management (web browser)	44
Reset the network settings to the factory default	44
Print the Printer Settings Page	44
Other Information	45
Safety precautions	45
To use the printer safely	45
Regulations	47
Federal Communications Commission (FCC) Declaration of Conformity (USA only)	47
Important	47
Important - about the interface cable	47
Radio interference	47
Industry Canada Compliance Statement (For Canada only)	47
EC Declaration of Conformity (For EU only)	47
International ENERGY STAR® Compliance Statement	47
Disconnect device	48
EU Directive 2002/96/EC and EN50419	48
IMPORTANT - For Your Safety	48
LAN connection	48
Wiring information (UK only)	48
Warning - This printer must be earthed.	48
Shipment of the printer	49
Repacking Instructions	49
Supplied CD-ROM	51
Windows®	51
Macintosh	51
Control panel	52