Brother International RH-981A Instruction Manual - English - Page 50

Cycle program, Program No.

Get Brother International RH-981A PDF manuals and user guides View all Brother International RH-981A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

6. OPERATION 6-4. Cycle program Cycle programs can consist of up to a maximum of four independent programs (A to D). A single cycle program can contain up to a maximum of eight steps. The following shows an example of storing a cycle program into cycle program A that consists of four steps of program 1 with knife operation on, and one step of program 3 with knife operation off. Program No. Knife operation Step 1 1 ON Step 2 1 ON Step 3 1 ON Step 4 1 ON Step 5 3 OFF 3052Q 2410Q 1. Press the SELECT key (1) to change the mode to automatic, manual or test feed mode. 2. Press the and keys to select cycle program "A". Note: Cycle program mode is not available if an independent program has been selected. 3. Press the SELECT key (1). The cycle program mode indicator (2) will illuminate. * The cycle program number "A" and the step number "1" will appear in the program number display (3), and the cycle program details will appear in the detail display (4). 4. Press the and keys to change the setting for step 1 to "1.", and then press the ENTER key (5) to accept the "1." setting. * "." signifies that knife operation is on. * "-" signifies a clear status. If "-" is set, the setting details for all subsequent steps will be cleared. 5. Press the and keys to change the step number to "2", and then repeat step 4 above. 6. Press the and keys to change the step number to "3", and then repeat step 4 above. 7. Press the and keys to change the step number to "4", and then repeat step 4 above. 8. Press the and keys to change the step number to "5". 9. Press the and keys to change the setting for step "5" to "3.". 10. Press the OFF key (6) so that the "." disappears, and then press the ENTER key (5) to accept the "3" setting. 11. Press the SELECT key (1). Cycle program mode will end and the mode will change to automatic mode. 2411Q RH-981A 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
6. OPERATION
RH-981A
43
6-4. Cycle program
Cycle programs can consist of up to a maximum of four independent programs (A to D).
A single cycle program can contain up to a maximum of eight steps.
The following shows an example of storing a cycle program into cycle program A that consists of four steps of
program 1 with knife operation on, and one step of program 3 with knife operation off.
Step 1
Step 2
Step 3
Step 4
Step 5
Program No.
1
1
1
1
3
Knife operation
ON
ON
ON
ON
OFF
1.
Press the SELECT key (1) to change the mode to
automatic, manual or test feed mode.
2. Press the
and
keys to select cycle program
"A".
Note:
Cycle program mode is not available if an
independent program has been selected.
3. Press the SELECT key (1). The cycle program
mode indicator (2) will illuminate.
* The cycle program number "A" and the step
number "1" will appear in the program number
display (3), and the cycle program details will
appear in the detail display (4).
4. Press the
and
keys to change the setting for
step 1 to "1.", and then press the ENTER key (5) to
accept the "1." setting.
*
"." signifies that knife operation is on.
*
"-" signifies a clear status. If "-" is set, the setting
details for all subsequent steps will be cleared.
5. Press the
and
keys to change the step
number to "2", and then repeat step 4 above.
6. Press the
and
keys to change the step
number to "3", and then repeat step 4 above.
7. Press the
and
keys to change the step
number to "4", and then repeat step 4 above.
8. Press the
and
keys to change the step
number to "5".
9. Press the
and
keys to change the setting for
step "5" to "3.".
10. Press the OFF key (6) so that the "." disappears,
and then press the ENTER key (5) to accept the
"3" setting.
11. Press the SELECT key (1). Cycle program mode
will end and the mode will change to automatic
mode.
3052Q
2410Q
2411Q