Brother International RH-981A Instruction Manual - English - Page 63

Adjusting the needle and looper timing

Get Brother International RH-981A PDF manuals and user guides View all Brother International RH-981A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

9. STANDARD ADJUSTMENTS 9-2. Adjusting the needle and looper timing The distance by which the needle bar rises from its lowest position to the position where the tip of the eye looper and the center of the needle are aligned should be the same as the distance from its lowest position to the position where the tip of the right looper and the center of the needle are aligned. Before adjusting the looper timing, first adjust the stitch width (needle racking width). * Refer to "Adjusting the needle racking width (stitch width)" on page 60. The standard width is 3 mm. Lowest position When center of needle and of needle bar looper tip are aligned 3075Q 0952Q 3076Q 1. Move the needle bar to its lowest position. 2. Use calipers to measure the distance between the end of the needle bar (1) and the top of the holder base (2) when the needle bar is at its lowest position. 3. Turn the upper shaft pulley until the tip of the eye looper (4) and the center of the needle (3) are aligned when the needle (3) is at the inside sewing position, and then use the calipers to take the same measurement as taken in step 2. Find the difference between the measurements taken in this step and in step 2. 4. Follow the same procedure as in step 3. above to find the difference between the two measurements when the needle (3) is at the outside sewing position. * When the needle (3) is at the inside sewing position, the tip of the eye looper (4) should be aligned with the center of the needle (3), and when the needle (3) is at the outside sewing position, the tip of the right looper (5) should be aligned with the center of the needle (3). * The distance from the end of the needle bar (1) and the top of the holder base (2) should be the same when the needle (3) is at both the inside sewing position and the outside sewing position. 3077Q 3078Q 5. If adjustment is necessary, turn the looper base (6) in the direction indicated by the arrow in the illustration, loosen the screw (7), and then move the looper link clamp (8) up or down to tilt the LS-holder bracket (9) to the left or right (in the direction of the arrow). RH-981A 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
9. STANDARD ADJUSTMENTS
RH-981A
56
9-2. Adjusting the needle and looper timing
The distance by which the needle bar rises from its lowest position to the position where the tip of the eye looper and
the center of the needle are aligned should be the same as the distance from its lowest position to the position where
the tip of the right looper and the center of the needle are aligned.
Before adjusting the looper timing, first adjust the stitch width (needle racking width).
*
Refer to "Adjusting the needle racking width (stitch width)" on page 60. The standard width is 3 mm.
1. Move the needle bar to its lowest position.
2. Use calipers to measure the distance between the end of the needle bar (1) and the top of the holder base (2)
when the needle bar is at its lowest position.
3. Turn the upper shaft pulley until the tip of the eye looper (4) and the center of the needle (3) are aligned when the
needle (3) is at the inside sewing position, and then use the calipers to take the same measurement as taken in
step 2. Find the difference between the measurements taken in this step and in step 2.
4. Follow the same procedure as in step 3. above to find the difference between the two measurements when the
needle (3) is at the outside sewing position.
*
When the needle (3) is at the inside sewing position, the tip of the eye looper (4) should be aligned with the
center of the needle (3), and when the needle (3) is at the outside sewing position, the tip of the right looper (5)
should be aligned with the center of the needle (3).
*
The distance from the end of the needle bar (1) and the top of the holder base (2) should be the same when the
needle (3) is at both the inside sewing position and the outside sewing position.
5. If adjustment is necessary, turn the looper base (6) in the direction indicated by the arrow in the illustration, loosen
the screw (7), and then move the looper link clamp (8) up or down to tilt the LS-holder bracket (9) to the left or
right (in the direction of the arrow).
3075Q
3076Q
Lowest position
of needle bar
When center of needle and
looper tip are aligned
3077Q
3078Q
0952Q