Home » Brother International Manuals » Sewing Machines » Brother International RH-9820 » Manual Viewer

Brother International RH-9820 Basic Instruction Manual - English - Page 14

When embedding into the table

Get Brother International RH-9820 PDF manuals and user guides

View all Brother International RH-9820 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

4. INSTALLATION 4-1-2. When embedding into the table When embedding the machine head into the table, some extra components will be required, so contact the place of purchase for further details. NOTE: When embedding the machine head into the table, be sure to install the L-shaped table reinforcement plates. (Refer to "4-3. Installing the table reinforcement plates (embedded installation only)".) For pneumatic unit For L-shaped reinforcement plates For operation panel cord For control box 4 x 4 mm dia. 20 depth (From underneath table) For valve unit For cotton stand For table leg For bed support plate Shaded area should be C10 For operation panel 4 x 2 mm dia. 10 depth 2x 2mm dia. 10 depth (from underneath table) For power switch Melamine veneer panel 0339B 6 RH-9820

Section	Page
COVER	1
SAFETY INSTRUCTIONS	3
CONTENTS	8
1. CONVENIENT FUNCTION FOR SMOOTH SEWING	9
2. NAMES OF MAJOR PARTS	10
3. SEWING SHAPES	11
4. INSTALLATION	12
4-1. Table processing diagram	12
4-1-1. When setting up on top of the table	13
4-1-2. When embedding into the table	14
4-2. Installing the control box	15
4-3. Installing the table reinforcement plates (embedded installation only)	16
4-4. Installing the machine head	16
4-4-1. When setting up on top of the table	16
4-4-2. When embedding into the table	18
4-5. Tilting back and returning the machine head	19
4-6. Installing the belt cover and feed bar cover U	20
4-7. Installing the oiler	20
4-8. Installing the operation panel	21
4-9. Installing the cotton stand	21
4-10. Installing the air unit and valve unit	22
4-11. Installing the 2-pedal foot switch (when using the 2-pedal foot switch)	22
4-12. Installing the treadle unit (when using the treadle)	23
4-12-1. When setting up on top of the table	23
4-12-2. When embedding into the table	23
4-13. Installing the hand start switch (when using the hand start switch)	24
4-14. Connecting the cords	26
4-14-1. Connecting the connectors inside the control box	26
4-14-2. Connecting the ground wire	30
4-14-3. Connecting the power cord	31
4-14-4. Connecting the air tubes	32
4-14-5. Securing the cords	32
4-15. Installing the air hose	33
4-16. Adjusting the air pressure	33
4-17. Installing the eye guard	34
4-18. Setting the scrap holder for the knife	34
4-19. Installing and removing the work clamp plates	35
4-20. Lubrication	36
4-20-1. Adding oil	36
4-20-2. Lubrication	37
5. PREPARATION BEFORE SEWING	38
5-1. Installing the needle	38
5-2. Threading the upper thread	39
5-3. Threading the lower thread	40
5-4. Threading the gimp	41
5-5. Setting the material	42
6. USING THE SEWING MACHINE (OPERATION PANEL: BASIC OPERATION)	43
6-1. Name and function of each operation panel item	43
6-2. Starting the sewing machine	45
6-3. Program setting method	46
6-3-1. Parameter list	48
6-4. Checking the sewing pattern in test mode	53
6-5. Switching cutting operation	55
6-6. Changing the material setting position	56
6-7. Using threading mode	57
7. USING THE SEWING MACHINE (SEWING OPERATION)	58
7-1. Automatic sewing (automatic mode)	58
7-2. Using the STOP switch	59
7-2-1. Pausing sewing during automatic sewing	59