Home » Brother International Manuals » Sewing Machines » Brother International RH-9820 » Manual Viewer

Brother International RH-9820 Basic Instruction Manual - English - Page 27

INSTALLATION, <Main P.C. board&gt

Get Brother International RH-9820 PDF manuals and user guides

View all Brother International RH-9820 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

4. INSTALLATION Securely lock the cord clamps. * Be sure to make the ground connection. (Refer to "4-14-2. Connecting the ground wire".) 0366B Connectors X pulse motor encoder 5-pin white Y pulse motor encoder 5-pin blue θ-feed motor encoder 5-pin black Treadle, 2-pedal foot switch, hand start switch 10-pin Operation panel 8-pin Hammer position sensor Machine head safety switch 3-pin (Y home position, cooling fan) sensor 12-pin STOP switch 6-pin (Zigzag check, low thread trimming OFF) sensor 6-pin Valve harness 12-pin Hammer valve harness 10-pin At main P.C. board Insertion location P20 (X-ENC) P4 (Y-ENC) P5 (P-ENC) P6 (FOOT) P1 (PANEL) P3 (CUTTER) P9 (HEAD-SW) P8 (SENSOR1) P13 (HEAD) P10 (SENSOR2) P12 (AIR1) P25 (AIR2) Cord clamp (5) (5) (5) (5) (5) (6) (6) (6) (6) (6) (7), (8) (7), (8) RH-9820 (Continued on next page) 19

Section	Page
COVER	1
SAFETY INSTRUCTIONS	3
CONTENTS	8
1. CONVENIENT FUNCTION FOR SMOOTH SEWING	9
2. NAMES OF MAJOR PARTS	10
3. SEWING SHAPES	11
4. INSTALLATION	12
4-1. Table processing diagram	12
4-1-1. When setting up on top of the table	13
4-1-2. When embedding into the table	14
4-2. Installing the control box	15
4-3. Installing the table reinforcement plates (embedded installation only)	16
4-4. Installing the machine head	16
4-4-1. When setting up on top of the table	16
4-4-2. When embedding into the table	18
4-5. Tilting back and returning the machine head	19
4-6. Installing the belt cover and feed bar cover U	20
4-7. Installing the oiler	20
4-8. Installing the operation panel	21
4-9. Installing the cotton stand	21
4-10. Installing the air unit and valve unit	22
4-11. Installing the 2-pedal foot switch (when using the 2-pedal foot switch)	22
4-12. Installing the treadle unit (when using the treadle)	23
4-12-1. When setting up on top of the table	23
4-12-2. When embedding into the table	23
4-13. Installing the hand start switch (when using the hand start switch)	24
4-14. Connecting the cords	26
4-14-1. Connecting the connectors inside the control box	26
4-14-2. Connecting the ground wire	30
4-14-3. Connecting the power cord	31
4-14-4. Connecting the air tubes	32
4-14-5. Securing the cords	32
4-15. Installing the air hose	33
4-16. Adjusting the air pressure	33
4-17. Installing the eye guard	34
4-18. Setting the scrap holder for the knife	34
4-19. Installing and removing the work clamp plates	35
4-20. Lubrication	36
4-20-1. Adding oil	36
4-20-2. Lubrication	37
5. PREPARATION BEFORE SEWING	38
5-1. Installing the needle	38
5-2. Threading the upper thread	39
5-3. Threading the lower thread	40
5-4. Threading the gimp	41
5-5. Setting the material	42
6. USING THE SEWING MACHINE (OPERATION PANEL: BASIC OPERATION)	43
6-1. Name and function of each operation panel item	43
6-2. Starting the sewing machine	45
6-3. Program setting method	46
6-3-1. Parameter list	48
6-4. Checking the sewing pattern in test mode	53
6-5. Switching cutting operation	55
6-6. Changing the material setting position	56
6-7. Using threading mode	57
7. USING THE SEWING MACHINE (SEWING OPERATION)	58
7-1. Automatic sewing (automatic mode)	58
7-2. Using the STOP switch	59
7-2-1. Pausing sewing during automatic sewing	59