Canon LV-X2 Owners Manual - Page 19

Basic Operation

Get Canon LV-X2 PDF manuals and user guides View all Canon LV-X2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

BASIC OPERATION TURNING ON / OFF THE PROJECTOR TURNING ON THE PROJECTOR 1 Complete peripheral connections (with Computer, VCR, etc.) before turning on the projector. (Refer to "CONNECTING PROJECTOR" on page 11~13 for connecting the equipment.) 2 Connect the projector's AC Power Cord into an AC outlet. LAMP Indicator lights red, and READY Indicator lights green. 3 Press POWER ON-OFF button on Top Control or on Remote Control Unit to ON. LAMP Indicator dims, and Cooling Fans start to operate. Preparation Display appears on a screen and the count-down starts. The signal from PC or Video source appears after 30 seconds. And then current image level is displayed on screen for 4 seconds. 30 Preparation Display disappears after 30 seconds. Current image level is displayed on screen for 4 seconds. TURNING OFF THE PROJECTOR 1 Press POWER ON-OFF button on Top Control or on Remote Control Unit, and a message "Power off?" appears on a screen. 2 Press POWER ON-OFF button again to turn off the projector. LAMP Indicator lights bright and READY Indicator turns off. After the projector is turned off, Cooling Fans operate (for 90 seconds). 3 When the projector has cooled down, READY Indicator lights green again. Power off? Message disappears after 4 seconds. NOTE : Projector cannot be turned on during cooling period with READY Indicator off. You can turn it on again after READY Indicator lights green. TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF. DO NOT DISCONNECT AC POWER CORD BEFORE READY INDICATOR LIGHTS GREEN. note on operation When "Power management" function is ON, the projector detects signal interruption and turns off Projection Lamp automatically. Refer to "Power management" on page 36. When WARNING TEMP. Indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes before turning on the projector again. When WARNING TEMP. Indicator continues to flash, follow the procedures below: 1. Press POWER ON-OFF button to turn the projector off and disconnect AC Power Cord from an AC outlet. 2. Check Air Filters for dust accumulation. 3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 39.) 4. Turn the projector on again. If WARNING TEMP. Indicator continues to flash, contact your sales dealer or service center. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
19
BASIC OPERATION
TURNING ON THE PROJECTOR
Connect the projector's AC Power Cord into an AC outlet.
LAMP
Indicator lights red, and READY Indicator lights green.
Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON.
LAMP Indicator dims, and Cooling Fans
start to operate.
Preparation Display appears on a screen and
the count-down starts.
The signal from PC or Video source
appears after 30 seconds.
And then current image level is
displayed on screen for 4 seconds.
2
3
TURNING OFF THE PROJECTOR
Press POWER ON-OFF button on Top Control or on Remote
Control Unit, and a message "Power off?" appears on a screen.
Press POWER ON-OFF button again to turn off the projector.
LAMP Indicator lights bright and READY Indicator turns off.
After the projector is turned off, Cooling Fans operate (for 90
seconds).
1
2
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
DO NOT DISCONNECT AC POWER CORD BEFORE
READY INDICATOR LIGHTS GREEN.
TURNING ON / OFF THE PROJECTOR
When WARNING TEMP. Indicator flashes red, the projector is automatically turned off.
Wait at least 5 minutes before
turning on the projector again.
When WARNING TEMP. Indicator continues to flash, follow the procedures below:
1. Press POWER ON-OFF button to turn the projector off and disconnect AC Power Cord from an AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters.
(See "AIR FILTER CARE AND CLEANING" section on page 39.)
4. Turn the projector on again.
If WARNING TEMP. Indicator continues to flash, contact your sales dealer or service center.
1
Complete peripheral connections (with Computer, VCR, etc.)
before turning on the projector.
(Refer to "CONNECTING
PROJECTOR" on page 11~13 for connecting the equipment.)
3
When the projector has cooled down, READY Indicator lights
green again.
30
Preparation Display disappears after 30 seconds.
Power off?
Message disappears after 4 seconds.
When
“
Power management
”
function is ON, the projector detects signal interruption and turns off Projection Lamp
automatically.
Refer to
“
Power management
”
on page 36.
NOTE : Projector cannot be turned on during cooling period with
READY Indicator off.
You can turn it on again after READY
Indicator lights green.
note on operation
Current image level is displayed on screen for 4
seconds.