Canon MF6530 Service Manual - Page 181
Error Code - system error e197
UPC - 013803056037
View all Canon MF6530 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 181 highlights
13.1 Error Code 13.1.1 List of Error Codes Display Code E000 Detail Code 0000 E001 0000 0001 E002 0000 E003 0000 0001 E010 0000 E100 0000 E196 0001 0002 E197 0000 E716 0000 E730 E733 0000 0000 E736 0000 E739 0000 Chapter 13 T-13-1 0011-6947 Main Cause/Symptom Countermeasure Startup error The temperature detected by the main or sub thermistor does - Check the fixing film connector. not rise to the specified value during startup control. - Replace the fixing film unit. - Replace the DC controller PCB. Abnormally high temperature (detected by main thermistor) The main thermistor detected an abnormally high temperature - Check the connector of the fixing film unit. (235 deg C) during temperature control. - Replace the fixing film unit. - Replace the DC controller PCB. Abnormally high temperature (detected by sub thermistor) The sub thermistor detected an abnormally high temperature - Check the connector of the fixing film unit. (300 deg C) during temperature control. - Replace the fixing film unit. - Replace the DC controller PCB. Low temperature during temperature control. The target temperature is not reached during temperature control. - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. Abnormally low temperature (detected by main thermistor) After the temperature detected by the main thermistor has reached the specified value, it does not reach the specified value during initial rotation. - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. Abnormally low temperature (detected by sub thermistor) After the temperature detected by the sub thermistor has reached the specified value, it does not reach the specified value during initial rotation. - Check the connector of the fixing film unit. - Replace the fixing film unit. - Replace the DC controller PCB. Main motor failure The main motor is faulty. - Check the connector of the main motor. - Replace the main motor. - Replace the DC controller PCB. BD detection PCB failure The BD detection PCB is faulty. - Check the connector of the BD detection PCB. - Replace the laser scanner unit. - Replace the DC controller PCB. Flash ROM write/read error - Replace the image processor PCB. The write/read of Flash ROM in the image processor PCB is faulty. PCL ROM write/read error The write/read of PCL ROM in the image processor PCB is faulty. - Replace the PCL PCB. - Replace the image processor PCB. Printer engine communication error Erroneous communication between the DC controller PCB and - Check the connectors of the DC controller PCB and image image processor PCB was detected. processor PCB. - Replace the DC controller PCB for normal connection. - Replace the image processor PCB. Erroneous communication with optional cassette Disconnection of the optional cassette was detected after power-on, detection of normal connection to the optional cassette, and start of communication. - Check the connectors of the optional cassette PCB and DC controller PCB. - Replace the optional cassette PCB for normal connection. - Replace the DC controller PCB. inside error of the image processor PCB (PDL system error) - Replace the image processor PCB. The inside of the image processor PCB is faulty. Erroneous communication between controller and printer Cannot communicate with the printer at startup. - Check the connectors of the DC controller PCB and image processor PCB for normal connection. - Check the power supply of the printer (Check whether initialization is performed at startup). - Replace the DC controller PCB or image processor PCB. CCU communication error The installed modem PCB is incompatible. - Check the connectors of the image processor PCB and modem. - Replace the modem PCB. - Replace the image processor PCB. Erroneous communication between controller and network board The installed network board is incompatible. - Check the connectors of the image processor PCB and LAN PCB for normal connection. - Replace the LAN PCB. - Replace the image processor PCB. 13-1