Canon MF6530 Service Manual - Page 202
Numeric Parameter Settings NUMERIC Param.
UPC - 013803056037
View all Canon MF6530 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 202 highlights
Chapter 14 No. Function Range of settings 008 V.34 modulation speed upper 0:3429, 1:3200, 2:3000, 3:2800, 4:2743, 5:2400 limit 009 V34 data speed upper limit 0:33.6 kbps, 1:31.2 kbps, 2:28.8 kbps, 3:26.4 kbps, 4:24.0 kbps, 5:21.6 kbps, 6:19.2 kbps, 7:16.8 kbps, 8:14.4 kbps, 9:12.0 kbps, 10:9.6 kbps, 11:7.2 kbps, 12:4.8 kbps, 13:2.4 kbps 010 Frequency of pseudoring signal 0:50 Hz, 1:25 Hz, 2:17 Hz 14.4.2 0011-4138 Use it to enable-disable the NL equalizer. If errors occur often during communication because of the condition of the line, enable (ON) the NL equalizer. Any of the following error codes may be indicated at time of transmission because of the line condition: ##100, ##101, ##102, ##104, ##201, ##281, ##282, ##283, ##750, ##755, ##765, ##774, ##779, ##784, ##789 Any of the following error codes may be indicated at time of transmission because of the line condition: ##103, ##107, ##114, ##201, ##790, ##793 14.4.3 0011-4141 Use it to s the telephone line monitor function: DIAL: generate the monitor sound of the telephone line using the speaker from the start of transmission to DIS. SERVICEMAN [1]: generate the monitor sound of the telephone line using the speaker from the start of communication to the end of it. SERVICEMAN [2]: generate the monitor sound of the telephone line2 (Option). OFF: do not generate the monitor sound of the telephone line using the speaker. 14.4.4 0011-4142 Use it to set the transmission level (ATT). Raise the transmission level if errors occur frequently at time of communication because of the condition of the line. (It means close to 8) Any of the following error codes may be indicated at time of transmission because of the line condition: ##100, ##101, ##102, ##104, ##201, ##280, ##281, ##282, ##283, ##284, ##750, ##752, ##754, ##755, ##757, ##759, ##760, ##762, ##764, ##765, ##767, ##769, ##770, ##772, ##774, ##775, ##777, ##779, ##780, ##782, ##784, ##785, ##787, ##789 Any of the following error codes may be indicated at time of reception because of the line condition: ##103, ##106, ##107, ##201, ##793 14.4.5 0011-4143 Use it to set an upper limit to the modulation speed (baud rate) for the V.34 primary channel. 14.4.6 0011-4145 Use it to set an upper limit to the data transmission speed for the V.34 primary channel between 2.4K and 33.6K bps in increments of 2400 bps. (0: 2.4K to 13: 33.6K bps). 14.4.7 0011-4146 You may select a frequency for the pseudo CI signal. Some types of external telephones do not ring when the fax/tel switch-over function is ON. To sound the ring, change the pseudo CI signal. 14.5 Numeric Parameter Settings (NUMERIC Param.) 14.5.1 T-14-14 No. Item 002 RTN transmission condition(1) 003 RTN transmission condition (2) 004 RTN transmission condition (3) 005 NCC pause time length (pre-ID code) 006 NCC pause time length (post-ID code) 010 line condition identification time length 011 T.30T1 timer (for reception) 013 T.30 EOL timer 015 hooking detection time length 016 time length to first response at time of fax/tel switchover 017 pseudo RBT signal pattern ON time length 018 pseudo RBT signal pattern OFF time length (short) 019 pseudo RBT signal pattern OFF time length (long) 020 pseudo CI signal pattern ON time length 021 pseudo CI signal pattern OFF time length (short) 022 pseudo CI signal pattern OFF time length (long) 023 CNG detection level at time of fax/tel switchover 0011-4147 Range of settings 1% to 99% 2 to 99 item 1 to 99 lines 1 to 60 sec 1 to 60 sec 0 to 9999 (10 msec) 0 to 9999 (10 msec) 500 to 3000 (10 msec) 0 to 999 0 to 9 0 to 999 0 to 999 0 to 999 0 to 999 0 to 999 0 to 999 0 to 7 14-12