Canon MF6530 Service Manual - Page 199
Detailed Discussions of Bit 7
UPC - 013803056037
View all Canon MF6530 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 199 highlights
Chapter 14 Bit Function 1 0 4 the length of the period of ignoring low speed signals after 1500 ms CFR output 700 ms 5 not used - - 6 CNG signal for manual transmission Not transmitted Transmitted 7 CED signal for manual reception Not transmitted Transmitted 14.3.4.2 Detailed Discussions of Bit 2 0011-4098 Use it to select the number of last flag sequences for a protocol signal (transmission speed at 300 bps). Select '2' if the other party fails to receive the protocol signal properly. Memo: Any of the following error codes may be indicated at time of transmission ##0100, ##0280, ##0281, ##0750, ##0753, ##0754, ##0755, ##0758, ##0759, ##0760, ##0763 ##0764, ##0765, ##0768, ##0769,##0770, ##0773, ##0775, ##0778, ##0780, ##0783, ##0785, ##0788 14.3.4.3 Detailed Discussions of Bit 3 0011-4099 Use it to select an appropriate reception mode after transmission of the CFR signal. If errors occur frequently at time of reception because of the condition of the line, select 'high speed' for reception mode and, at the same time, selects 'do not receive' for 'ECM reception.' Memo: Any of the following error codes may be indicated at time of reception because of line condition ##0107, ##0114, ##0201 Be sure to change bit 4 before changing this bit; if errors still occur, change this bit. When 'high speed' is selected, only high-speed signals (images) will be received after transmission of the CFR signal. 14.3.4.4 Detailed Discussions of Bit 4 0011-4100 Use it to select the time length during which low-speed signals are ignored after transmission of the CFR signal. If the condition of the line is not good and, therefore, the reception of image signals is difficult, select '1500 ms.' 14.3.4.5 Detailed Discussions of Bit 6 0011-4101 Selects whether or not to transmit CNG signal during manual transmission. In manual transmitting to a fax with the FAX/TEL switching mode, if there are frequent errors due to failure to switch to fax mode, select "Transmitted" for the CNG signal. 14.3.4.6 Detailed Discussions of Bit 7 0011-4102 Selects whether or not to transmit CED signals during manual reception. If the other fax does not transmit even when you start manual reception, select "Transmitted" for the CED signal. 14.3.5 SSSW-SW05 14.3.5.1 List of Functions T-14-4 0011-4103 Bit Function 1 0 0 not used - - 1 Conversion from mm to inch (text mode) convert do not convert 2 Conversion from mm to inch (text/photo mode) convert do not convert 3 not used - - 4 not used - - 5 not used - - 6 not used - - 7 not used - - 14.3.5.2 Detailed Discussions of Bit 1 0011-4104 Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text mode. Scanning direction in conversion follows the Bit 2 setting of SW14. 14.3.5.3 Detailed Discussions of Bit 2 0011-4105 Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text/photo mode while bit 1 is set to '1'. Scanning direction in conversion follows the Bit 2 setting of SW14. 14.3.6 SSSW-SW12 14.3.6.1 List of Functions T-14-5 0011-4106 Bit Function 1 0 0 Time-out period for one page upon transmission 1 0 1 Time-out period for one page upon transmission 1 0 2 not used - - 3 not used - - 14-9