Canon MF6530 Service Manual - Page 201
Menu Switch Settings MENU
UPC - 013803056037
View all Canon MF6530 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 201 highlights
Chapter 14 either in sub scanning direction only or in both main and sub scanning directions. The setting is valid only when bit 1 of SW05 of #SSSW is set to '1'. 14.3.8.3 Detailed Discussions of Bit 4 0011-4111 Use it to specify whether to declare or not declare an inch-configuration resolution to the other machine for G3 communication: if 'declare' is selected, the machine will indicate that it reads and records at an inch-configuration resolution using the DIS, DCS, or DTC signal. 14.3.9 SSSW-SW28 14.3.9.1 List of Functions T-14-11 0011-4112 Bit Function 1 0 0 Caller V.8 protocol NO YES 1 Called party V.8 protocol NO YES 2 Caller V.8 protocol late start NO YES 3 Called party V.8 protocol late start NO YES 4 V.34 reception fallback Prohibited Not prohibited 5 V.34 transmission fallback Prohibited Not prohibited 6 not used - - 7 not used - - 14.3.9.2 Detailed Discussions of Bit 0 0011-4113 Select whether to use the V.8 protocol when calling. If NO is selected, the V.8 protocol is inhibited at calling and the V.21 protocol is used. 14.3.9.3 Detailed Discussions of Bit 1 0011-4114 Select whether to use the V.8 protocol when called. If NO is selected, the V8 protocol is inhibited when called and the V.21 protocol is used. 14.3.9.4 Detailed Discussions of Bit 2 0011-4115 If ANSam signal is not received during transmission, select whether to use the V.8 protocol when the other fax machine declares the V.8 protocol in DIS signal. If NO is selected, the CI signal is not transmitted and the V.8 protocol is not used even if the DIS that specifies the V.8 protocol is received. The V.8 late start is not executed during manual transmission regardless of this setting. 14.3.9.5 Detailed Discussions of Bit 3 0011-4116 Select whether to declare the V.8 protocol in DIS signal for reception. If NO is selected, the V.8 protocol cannot be used because it is not declared in DIS signal. The V.8 late start is not executed during manual reception regardless of this setting. 14.3.9.6 Detailed Discussions of Bit 4 0011-4117 Select whether the receiver falls back during V.34 reception. If 'Prohibit' is selected, the receiver does not fall back. 14.3.9.7 Detailed Discussions of Bit 5 0011-4118 Select whether the transmitter falls beck during V.34 transmission. If 'Prohibit' is selected, teh transmitter does not fall back. 14.3.10 SSSW-SW30 14.3.10.1 List of Functions T-14-12 0011-4123 Bit Function 1 0 0 Not used - - 1 Not used - - 2 Not used - - 3 Not used - - 4 Not used - - 5 New dial tone detection method Detect with the new Detect with the method. existing method. 6 Not used - - 7 Not used 14.3.10.2 Detailed Discussions of Bit 5 - - 0011-4124 When "Detect with the new method" is selected, tone is detected for 3.5 seconds before call origination in order to discriminate between dial tone and voice. If dial tone is detected and the time since line seizure is 3.5 seconds or longer, call origination takes place immediately. If the time since line seizure is less than 3.5 seconds, call origination takes place after waiting for 1 second. (If the time since line seizure reaches 3.5 seconds during the 1-second waiting period, call origination takes place immediately. By default, "Detect with a new method" is assigned for this SW. 14.4 Menu Switch Settings (MENU) 14.4.1 Menu Switch Composition T-14-13 0011-4137 No. Function 005 NL equalizer 006 telephone line monitor 007 transmission level (ATT) Range of settings 1: ON, 0: OFF 0:DIAL, 1:SERVICEMAN1, 2:SERVICEMAN2, 3:OFF from 0 to 15 (ex: 15= -15 dBm) 14-11