Chamberlain B2210T Installation Manual - English Spanish - Page 12

STEP 4 Install theBelt,

Get Chamberlain B2210T PDF manuals and user guides View all Chamberlain B2210T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Assembly STEP4Install theBelt 1. Pull the belt around the idler pulley and toward the trolley. The ribbed side must contact the pulley. 2. Hook the trolley connector into the retaining slot on the trolley as shown (Figure 1). 3. With the trolley against the screwdriver, dispense the remainder of the belt along the rail length toward the motor unit and around the sprocket (Figure 2). The sprocket teeth must engage the belt. 4. Check to make sure the belt is not twisted. Connect the trolley threaded shaft with the master link (Figure 3). a. Push pins of master link bar through holes in end of belt and trolley threaded shaft. b. Push master link cap over pins and past pin notches. c. Slide the closed end of the clip-on spring over one of the pins. Push the open end of the clip-on spring onto the other pin. 5. Remove the spring trolley nut from the threaded shaft. 6. Insert the trolley threaded shaft through the hole in the trolley. HARDWARE Threaded Shaft with Spring Trolley Nut Master Link Figure 1 Trolley Connector Figure 2 Sprocket Retaining Slot Master Link Threaded Shaft Figure 3 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
12
HARDWARE
Threaded Shaft with Spring Trolley Nut
Master Link
Figure 1
Trolley
Connector
Retaining
Slot
Master Link
Figure 2
Sprocket
Threaded Shaft
Figure 3
Assembly
STEP4Install theBelt
1.
Pull the belt around the idler pulley and toward the trolley. The ribbed side must contact the pulley.
2.
Hook the trolley connector into the retaining slot on the trolley as shown (Figure 1).
3.
With the trolley against the screwdriver, dispense the remainder of the belt along the rail length
toward the motor unit and around the sprocket (Figure 2). The sprocket teeth must engage the belt.
4.
Check to make sure the belt is not twisted. Connect the trolley threaded shaft with the master link
(Figure 3).
a.
Push pins of master link bar through holes in end of belt and trolley threaded shaft.
b.
Push master link cap over pins and past pin notches.
c.
Slide the closed end of the clip-on spring over one of the pins. Push the open end of the clip-on
spring onto the other pin.
5.
Remove the spring trolley nut from the threaded shaft.
6.
Insert the trolley threaded shaft through the hole in the trolley.