Chamberlain B2210T Installation Manual - English Spanish - Page 26

STEP 11 Wire the Door Control to the Garage Door Opener, STEP 12 Attach the Warning Labels

Get Chamberlain B2210T PDF manuals and user guides View all Chamberlain B2210T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Installation STEP 11 Wire the Door Control to the Garage Door Opener 1. Run the white and red/white wire from the door control to the garage door opener. Attach the wire to the wall and ceiling with the staple (not applicablefor gang box or pre-wired installations). Do not pierce the wire with the stapleas this may cause a short or an open circuit. 2. Strip 7/16" (11 mm) of insulation from the end of the wirenear the garagedoor opener. 3. Connect the wire to the red and white terminals on the garage door opener. If your garage is pre-wired make sure you use the same wires that are connected to the door control. To insert or release wires from the terminal, push in the tab with screw driver tip. HARDWARE Insulated Staple (Not Shown) 1 2 7/16" (11 mm) Staple STEP 12 Attach the Warning Labels 1. Attach the entrapment warning label on the wall near the door control with tacks or staples. 2. Attach the manual release/safety reverse test label in a visible location on the inside of the garage door. 3 RED WHITE 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
26
1
3
Staple
2
7/16” (11 mm)
HARDWARE
Insulated Staple (Not Shown)
Installation
STEP 11 Wire the Door Control to the Garage Door Opener
1.
Run the white and red/white wire from the door control to the garage door opener. Attach the wire to
the wall and ceiling with the staple (not applicablefor gang box or pre-wired installations). Do not pierce
the wire with the stapleas this may cause a short or an open circuit.
2.
Strip 7/16” (11 mm) of insulation from the end of the wirenear the garagedoor opener.
3.
Connect the wire to the red and white terminals on the garage door opener. If your garage is pre-wired
make sure you use the same wires that are connected to the door control. To insert or release wires from
the terminal, push in the tab with screw driver tip.
STEP 12 Attach the Warning Labels
1.
Attach the entrapment warning label on the wall near the door control with tacks or staples.
2.
Attach the manual release/safety reverse test label in a visible location on the inside of the garage
door.
WHITE
RED