Chamberlain B2210T Installation Manual - English Spanish - Page 31

Step 15 Connect Power, Optiona- Typicalwiring, Option B- Permanentwiring

Get Chamberlain B2210T PDF manuals and user guides View all Chamberlain B2210T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Installation STEP 15 Connect Power To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: l Be sure power is NOT connected to the opener, and disconnect power to circuit BEFORE removing cover to establish permanent wiring connection. l Garage door installation and wiring MUST be in compliance with ALL local electrical and building codes. l NEVER use an extension cord, 2-wire adapter, or change plug in ANY way to make it fit outlet. Besure the opener is grounded. To avoid installation difficulties, do not run the opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, contact a qualified electrician to install the proper outlet. THERE ARE TWO OPTIONS FOR CONNECTING POWER: OPTIONA- TYPICALWIRING 1. Plug in the garage door opener into a grounded outlet. 2. DO NOT run garage door opener at this time. OPTION B- PERMANENTWIRING If permanent wiring is required by your local code, refer to the following procedure. To make a permanent connection through the 7/8-inch hole in the top of the motor unit (according to local code): 1. Remove the motor unit cover screws and set the cover aside. 2. Remove the attached 3-prong cord. 3. Connect the black (line) wire to the screw on the brass terminal; the white (neutral) wire to the screw on the silver terminal; and the ground wire to the green ground screw. The opener must be grounded. 4. Re install the cover. Ground Tab Green Ground Screw Ground Wire White Wire Black Wire 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
31
To prevent possible SERIOUS INJURY or DEATH from electrocution or fire:
l
Be sure power is NOT connected to the opener, and disconnect power to circuit BEFORE removing cover
to establish permanent wiring connection.
l
Garage door installation and wiring MUST be in compliance with ALL local electrical and building
codes.
l
NEVER use an extension cord, 2-wire adapter, or change plug in ANY way to make it fit outlet. Besure the
opener is grounded.
To avoid installation difficulties, do not run the opener at this time.
To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding
pin. This plug will only fit into a grounding type outlet. If the plug doesn’t fit into the outlet you have, contact
a qualified electrician to install the proper outlet.
White Wire
Black Wire
Installation
STEP 15 Connect Power
THERE ARE TWO OPTIONS FOR CONNECTING POWER:
OPTIONA- TYPICALWIRING
1.
Plug in the garage door opener into a grounded outlet.
2.
DO NOT run garage door opener at this time.
OPTION B- PERMANENTWIRING
If permanent wiring is required by your local code, refer to the following procedure. To make a permanent
connection through the 7/8-inch hole in the top of the motor unit (according to local code):
1.
Remove the motor unit cover screws and set the cover aside.
2.
Remove the attached 3-prong cord.
3.
Connect the black (line) wire to the screw on the brass terminal; the white (neutral) wire to the screw on the
silver terminal; and the ground wire to the green ground screw.
The opener must be grounded.
4.
Re install the cover.
Ground Tab
Green Ground Screw
Ground Wire