Home » Cisco Manuals » Hubs & Switches » Cisco 4948-10GE » Manual Viewer

Cisco 4948-10GE Installation Guide - Page 25

Catalyst 4948 Switch Software Features - catalyst 48 port

UPC - 746320958668

Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Chapter 1 Product Overview Catalyst 4948 Switch Software Features Figure 1-3 Catalyst 4928-10GE Switch 271710 PS1 PS2 FAN STATUS 1 8 9 16 17 CON MGMT 24 25 26 ENABLED 27 28 Catalyst ME 4924 10GE 29 ENABLED 30 The Catalyst 4928-10GE switch has a 48-Gbps, nonblocking, full-duplex switching fabric, providing 102 million packets-per-second of switching capacity for high-speed applications. The Catalyst 4928-10GE chassis has 28 1000BASEX SFP ports, and two X2 10-Gigabit Ethernet uplink ports. All three switches have a removable automatic variable speed fan tray for low noise operation at room temperature and removable and redundant 300 W AC or 300 W DC power supply provides fault-tolerance protection for the switch. See the "Connecting AC Power to the Switch" section on page 3-9. Catalyst 4948 Switch Software Features The following is an overview of Catalyst 4948 features: • Layer 2, Layer 3, and Layer 4 switching services • Support for 32,768 MAC addresses for Layer 2 switching • Support for 2,048 VLANs and 4,096 VLAN IDs - IEEE 802.1Q VLAN tagging on all ports - Q-in-Q for EFM - Cisco Inter Switch Link (ISL) tagging on all ports • 16,000 multicast forwarding entries and 16,000 unicast forwarding entries • 512 ingress policers and 512 egress policers • 8,000 ingress Security ACEs (Access Control Entries) and 8,000 egress Security ACEs • Support for port aggregation using Port Aggregation Protocol (PAgP) for Gigabit EtherChannel 78-18039-02 Catalyst 4900 Series Switch Installation Guide 1-3

Section	Page
Catalyst 4900 Series Switch Installation Guide	1
Contents	5
Preface	9
Product Overview	23
Catalyst 4900 Series Switch Applications	24
Catalyst 4948 Switch Software Features	25
Catalyst 4948-10GE and Catalyst 4928-10GE Switch Software Features	26
Hardware System Features	28
Switch Components	29
Traffic Ports on the Catalyst 4948	29
Traffic Ports on the Catalyst 4948-10GE	29
Traffic Ports on the Catalyst 4928-10GE	29
Console Port	29
Front Panel LEDs	31
Chassis Cooling	33
Power Supplies	34
Environmental Monitoring of the Power Supplies	35
Power Management for the Switch	36
Power Management Modes	36
Site Planning	37
Site Environmental Requirements	37
Site Power Requirements	38
Pre-installation Requirements	39
Warnings and Cautions	39
EMI Recommendations	40
Power Requirements and Heat Dissipation	40
Grounding Requirements	42
Safety Overview	43
Ensuring Safety	43
Working Safely with Electricity	44
Preventing Electrostatic Discharge Damage	45
Site Planning Checklist	45
Installing the Switch	47
Verifying the Contents	47
Rack-Mounting the Switch	48
Rack-Mounting Guidelines	49
Lifting the Chassis Safely	51
Required Installation Tools	51
Rack-Mounting the Switch	52
Connecting AC Power to the Switch	55
Connecting DC Power to the Switch	57
Transceiver Modules	61
SFP Modules	61
SFP Modules and Alternative Wiring	61
X2 Modules	62
Module Maintenance Guidelines	65
Cleaning the Fiber-Optic Connectors	65
Additional Guidelines	67
Troubleshooting the Installation	69
Getting Started	70
Problem Solving to the System Component Level	70
Identifying Startup Problems	71
LED Readings	71
Troubleshooting the Power Supply	73
Contacting Customer Service	74
Specifications	75
Console Port	75
Management Port	76
Catalyst 4900 Series Switch Specifications	77
Initial Configuration for the Switch	79
Connecting to the Switch	80
Starting the Terminal-Emulation Software	81
Connecting to a Power Source	81
Entering the Initial Configuration Information	82
IP Settings	82
Performing the Initial Configuration	83
Compliance Information and Translated Safety Warnings	87
Translated Safety Warnings	88
Statement 1003-DC Power Disconnection	88
Statement 1004-Installation Instructions	90
Statement 1006-Chassis Warning for Rack-Mounting and Servicing	92
Statement 1008-Class 1 Laser Product	100
Statement 1011-Staring into Laser Beam	102
Statement 1017-Restricted Area	104
Statement 1019-Main Disconnecting Device	107
Statement 1024-Ground Conductor	109
Statement 1030-Equipment Installation	111
Statement 1040-Product Disposal	113
Statement 1045-Short-circuit Protection	116
Statement 1051-Laser Radiation	119
Statement 1074-Comply with Local and National Electrical Codes	122
Statement 1075-Hazardous Voltage or Energy Present on DC Power Terminals	123
Regulatory Standards Compliance	125
European Directives	128
Statement 287-Declaration of Conformity to R&TTE Directive 1999/5/EC for the European Community, Switzerland, Norway, Iceland and Liechtenstein	128
Statement 275-Declaration of Conformity with Regard to the Directives 73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC	130
California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations, Chapter 33)	132
EMC Class A Notices and Warnings	132
Class A Notice for FCC	132
Class A Notice for Canada	133
Statement 340-Class A Warning for CISPR22	133
Statement 191-VCCI Class A Warning for Japan	136
Statement 256-Class A Warning for Hungary	137
Statement 294-Class A Warning for Korea	137
Statement 257-Class A Notice for Taiwan and Other Traditional Chinese Markets	138
Statement 371-Power Cable and AC Adapter	138