Compaq Pro 4300 Maintenance & Service Guide Pro 4300 All-in-One Business P - Page 63

Processor, CAUTION,

Get Compaq Pro 4300 PDF manuals and user guides View all Compaq Pro 4300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Processor 1. Prepare the computer for disassembly (see Preparing to Disassemble the Computer on page 33). 2. Remove the center access panel (see Hinge Cover Panel on page 34). 3. Remove the memory access panel (see Memory Access Panel on page 36). 4. Remove the drive access panel (see Drive Access Panel on page 38). 5. Remove the heat sink cover (see Heat Sink Cover on page 52). 6. Remove the heat sink (see Heat Sink (Thermal Module) on page 54). 7. Rotate the locking lever to its full open position (1). 8. Raise and rotate the microprocessor retainer to its fully open position (2). 9. Carefully lift the processor from the socket (3). CAUTION: Do NOT handle the pins in the processor socket. These pins are very fragile and handling them could cause irreparable damage. Once pins are damaged it may be necessary to replace the system board. The heat sink must be installed within 24 hours of installing the processor to prevent damage to the processor's solder connections. Figure 6-35 Removing the processor To install a new processor: 1. Place the processor in its socket and close the retainer. Make sure the slot in the processor fits into the post on the socket. 2. Secure the locking lever. If reusing the existing heat sink, go to step 3. If using a new heat sink, go to step 6. 56 Chapter 6 Removal and Replacement Procedures All-in One (AIO) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Processor
1.
Prepare the computer for disassembly (see
Preparing to Disassemble the Computer
on page
33
).
2.
Remove the center access panel (see
Hinge Cover Panel
on page
34
).
3.
Remove the memory access panel (see
Memory Access Panel
on page
36
).
4.
Remove the drive access panel (see
Drive Access Panel
on page
38
).
5.
Remove the heat sink cover (see
Heat Sink Cover
on page
52
).
6.
Remove the heat sink (see
Heat Sink (Thermal Module)
on page
54
).
7.
Rotate the locking lever to its full open position
(1)
.
8.
Raise and rotate the microprocessor retainer to its fully open position
(2)
.
9.
Carefully lift the processor from the socket
(3)
.
CAUTION:
Do NOT handle the pins in the processor socket. These pins are very fragile and
handling them could cause irreparable damage. Once pins are damaged it may be necessary to
replace the system board.
The heat sink must be installed within 24 hours of installing the processor to prevent damage to
the processor’s solder connections.
Figure 6-35
Removing the processor
To install a new processor:
1.
Place the processor in its socket and close the retainer. Make sure the slot in the processor fits
into the post on the socket.
2.
Secure the locking lever. If reusing the existing heat sink, go to step 3. If using a new heat sink,
go to step 6.
56
Chapter 6
Removal and Replacement Procedures All-in One (AIO) Chassis