Craftsman 79193 Operation Manual - Page 6

IFCOLD..F. orcoldweathecrondition(bselow40°F)fl,ipthe 7. Squeeze and hold the throttle control to warm up the engine ColdWeatheSrtarLt eve(rFig7. )downtothe for 30 to 60 seconds. start/closepdositioanndcontinuteostep3. DONOT IF... flipthislevedr ownifthetemperatuisreabove40°R 3. Fullpyresasndreleastheeprimebrulb10timess,lowlyS.ome i..........I.F..... amouonftfuesl houlbdevisiblientheprimebrulb(Fig7.).Ifyou The engine does not start, go back to step 3. The engine stops while you are squeezing the throttle, go back to step 4. can'steefueilnthebulbp, resasndreleastheebulbasmany timeassittakesbeforyeoucanseefueilnit. STOPPING iNSTRUCTiONS 4. Withtheuniitnthe startinpgositiodno, Cold Weather Primer Bulb notsqueezthee Starter Lever throttlecontro(lFig. Run/Open 8).Pultlhestarteror pe untiul nist tarts. 1. Release your hand from the throttle control. Allow the engine to cool down by idling. 2. Press and hold the On/Off Control in the OFF (O) position until the unit comes to a complete stop. IFCOLD..F. orcold weather conditions (below40°F)fl,ip Close/Start theColdWeather StarLt evebrack Fig. 7 upto the rauftne/trohpeeupnnoitshiatison startedand beforesqueezing thethrottle control. Starting Position OPERATING THE CONVERTIBLE TM COUPLER SYSTEM WARNING: Before you begin using any attachment, read I and understand the manual that came with the attachment. Follow all safety information contained within. ! CAUTION: These attachments are to be snapped into i I the primary hole only. Using the wrong hole could lead to personal injury or damage to the unit. The Convertible TM coupler system enables the use of these optional attachments. For information about attachments, call 1=800=235=5878. 5. Squeeze the throttle control to warm up the engine for 30 to 60 seconds. IF... The engine does not start, go back to step 3. Fig. 8 IF... The engine stops while you are squeezing go back to step 4. the throttle, • Edger Cultivator Turbo Blower Brushcutter Pole Saw Blade Pruner Hedge Trimmer Garden Attachment REMOVING THE TRIMMER ATTACHMENT OR OTHER ATTACHMENT THE FOLLOWING iNSTRUCTiONS EXPLAIN HOW TO START THE UNiT USING THE ELECTRIC STARTER ACCESSORY. NOTE= THIS UNiT IS ELECTRIC START CAPABLE as an alternate starting method. Please refer to the Electric Starter operator's manual for proper installation and use of this feature. damage to the unit, shut the unit off before removing or WinsAtaRllNinIgNGat:tachTmoenatv.oid serious personal injury and 1. Turn the knob Convertible TM Release Button STARTING iNSTRUCTiONS 1. Check the oil level in the crankcase. Refer to Checking the Oil Level. 2. Fill the fuel tank with fresh, clean unleaded gasoline. Refer to Fueling the Unit. NOTE: There is no need to turn the unit on. The On/Off Control is in the ON (I) position at all times (Fig. 6). IF COLD... For cold weather conditions (below 40°F), flip the Cold Weather Start Lever (Fig. 7) down to the start/closed position and continue to step 3. DO NOT flip this lever down if the temperature is above 40°R clooousnetenrc(loFcigk.w1is1e). to Co_, 1 "_ ___ w/F 2. Press and hold the J " _-_ release button (Fig. 9). 3. While firmly holding the upper shaft, pull the trimmer attachment or other attachment straight Guide Recess out of the Convertible TM coupler (Fig. 10). Fig. 9 iNSTALLING THE TRIMMER ATTACHMENT OR OTHER ATTACHMENT Fully press and release the primer bulb 10 times, slowly. Some amount of fuel should be visible in the primer bulb (Fig. 7). If you can't see fuel in the bulb, press and release the bulb as many times as it takes before you can see fuel in it. 4. With the unit in the starting position (Fig. 8). Place the electric starter into the back of the unit. Refer to Operation section of the Electric Starter oeprator's manual. 5. Do Not squeeze the throttle control, press and hold the electric starter ON (I) button for 2 second intervals until unit starts. IF COLD... For cold weather conditions (below 40°F), flip the Cold Weather Start Lever back up to the run/open position. 6. Once the unit starts, remove the electric starter from the rear of the unit. release button is fully snapped into the primary hole (Fig. 10), _ anAdUthTaItOtNhe: knBobefo(rFeigo. p1e1r)aitsinsgectuhriselyuntiitg,hbteenseudr.e that the NOTE: To make installing or removing the attachment easier, place the unit on the ground or on a work bench. Primary Hole 1. Tcouurnntekrncolobckwise to loosen (Fig. 11). "f_"_-,-_ _.__, 2. Wtrimhimleerfirmaltytachhomldeinngt tohre _ other attachment, push it Upper Shaft straight into the ,___ Attachment Convertible TM coupler Shaft until the release button Fig. 10 snaps firmly into the primary hole (Fig. 10). 6