D-Link DGS-1100-08V2 User Manual 1.00 WW - Page 36

L2 Features > Link Aggregation

Get D-Link DGS-1100-08V2 PDF manuals and user guides View all D-Link DGS-1100-08V2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

4 Configuration D-Link Smart Managed Switch User Manual L2 Features > Link Aggregation The Link Aggregation function enables the combining of two or more ports together to increase bandwidth. Each Link Aggregation group supports a maximum of four ports. Figure 4.41 - L2 Features > Link Aggregation The fields that can be configured for Link Aggregation are described below: Item Description Link Aggregation Global Settings Link Aggregation Specify to enable or disable the Link Aggregation function. Channel Group Information ID Use the drop-down menu to select a link aggregation group. Port Select the ports to assign to the aggregation group. Table 4.25 Click Apply to make the configurations take effect. Click Delete to remove the Link Aggregation group. NOTE: Maximum number of ports in a Link Aggregation group is 4. DGS-1100-05V2/05PDV2 only supports 1 Link Aggregation group, and DGS1100-08V2/08PV2 supports up to 2 Link Aggregation groups. NOTE: Each combined port must be connected to devices within the same VLAN group. L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Settings With Internet Group Management Protocol (IGMP) snooping, the Smart Managed Switch can make intelligent multicast forwarding decisions by examining the contents of each frame's Layer 2 MAC header. By default, IGMP is disabled. If enabled, the Smart Managed Switch can recognize IGMP queries and reports sent between network stations or devices and an IGMP host. With IGMP snooping enabled, the Smart Managed Switch will forward multicast traffic only to the connections that requested it. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
4
Configuration
D-Link Smart Managed Switch User Manual
33
L2 Features > Link Aggregation
The Link Aggregation function enables the combining of two or more ports together to increase bandwidth.
Each Link Aggregation group supports a maximum of four ports.
Figure 4.41 – L2 Features > Link Aggregation
The fields that can be configured for
Link Aggregation
are described below:
Item
Description
Link Aggregation Global Settings
Link Aggregation
Specify to enable or disable the Link Aggregation function.
Channel Group Information
ID
Use the drop-down menu to select a link aggregation group.
Port
Select the ports to assign to the aggregation group.
Table 4.25
Click
Apply
to make the configurations take effect.
Click
Delete
to remove the Link Aggregation group.
NOTE:
Maximum number of ports in a Link
Aggregation group is 4. DGS-1100-05V2/05PDV2
only supports 1 Link Aggregation group, and DGS-
1100-08V2/08PV2
supports
up
to
2
Link
Aggregation groups.
NOTE:
Each combined port must be connected to
devices within the same VLAN group.
L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Settings
With Internet Group Management Protocol (IGMP) snooping, the Smart Managed Switch can make
intelligent multicast forwarding decisions by examining the contents of each frame’s Layer 2 MAC header.
By default, IGMP is disabled. If enabled, the Smart Managed Switch can recognize IGMP queries and
reports sent between network stations or devices and an IGMP host. With IGMP snooping enabled, the
Smart Managed Switch will forward multicast traffic only to the connections that requested it.