D-Link DGS-1100-24P Reference Guide - Page 81

Configuration Restore & Backup

Get D-Link DGS-1100-24P PDF manuals and user guides View all D-Link DGS-1100-24P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

D-Link DGS-1100 Series Switch User Manual Configuration Restore & Backup Configuration Restore from HTTP This window is used to initiate a configuration restore from a local PC using HTTP. Note: If the switch is in HTTPS mode, the firmware or configuration cannot be upgraded using regular HTTP. To view the following window, click Tools > Configuration Restore & Backup > Configuration Restore from HTTP, as shown below: Figure 13-7 Configuration Restore from HTTP window The fields that can be configured are described below: Parameter Source File Description Enter the source filename and path of the configuration file located on the local PC. Alternatively click the Browse button to navigate to the location of the configuration file located on the local PC. Click the Restore button to initiate the configuration restore. Click Effective immediately (running-config) to have the uploaded configuration loaded immediately. Click Take effect after the next boot (startup-config) to load the configuration after the switch has been rebooted. Configuration Restore from TFTP This window is used to initiate a configuration restore from a TFTP server. To view the following window, click Tools > Configuration Restore & Backup > Configuration Restore from TFTP, as shown below: Figure 13-8 Configuration Restore from TFTP window The fields that can be configured are described below: Parameter TFTP Server IP Source File Description Enter the TFTP server's IPv4 address here. Enter the source filename and path of the configuration file located on the TFTP server here. 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
D-Link DGS-1100 Series Switch User Manual
Configuration Restore & Backup
Configuration Restore from HTTP
This window is used to initiate a configuration restore from a local PC using HTTP.
Note
: If the switch is in HTTPS mode, the firmware or configuration cannot be upgraded using
regular HTTP.
To view the following window, click
Tools > Configuration Restore & Backup > Configuration
Restore from HTTP
, as shown below:
Figure 13-7 Configuration Restore from HTTP window
The fields that can be configured are described below:
Parameter
Description
Source File
Enter the source filename and path of the configuration file
located on the local PC. Alternatively click the
Browse
button
to navigate to the location of the configuration file located on
the local PC.
Click the
Restore
button to initiate the configuration restore.
Click
Effective immediately (running-config)
to have the uploaded configuration loaded
immediately.
Click
Take effect after the next boot (startup-config)
to load the configuration after the switch has
been rebooted.
Configuration Restore from TFTP
This window is used to initiate a configuration restore from a TFTP server.
To view the following window, click
Tools > Configuration Restore & Backup > Configuration
Restore from TFTP
, as shown below:
Figure 13-8 Configuration Restore from TFTP window
The fields that can be configured are described below:
Parameter
Description
TFTP Server IP
Enter the TFTP server’s IPv4 address here.
Source File
Enter the source filename and path of the configuration file
located on the TFTP server here.
75