D-Link DSN-3400-20 User Guide - Page 87

Restoring Factory Default Settings

Get D-Link DSN-3400-20 - Xstack 1X10GBE Iscsi San Array 3U PDF manuals and user guides
UPC - 790069299773
View all D-Link DSN-3400-20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

5.2.5 Restoring Factory Default Settings There may be times when you want to return the xStack Storage system to its factory default settings. Using the Restore Factory Defaults button in the Settings tab of the System Administration view, you can return the xStack Storage system to the settings that were in effect when it was shipped from the factory. However, any volumes you set up will remain intact. For a complete list of the xStack Storage's factory default settings, refer to Appendix B. 1. In the System Administration View, click the Settings tab to display the general settings in Figure 5-6 on page 75. Or if you are already in the Settings tab but another screen is displayed, click the General button on the left side of the Settings tab: 2. Under xStack Configuration, click the Restore Factory Defaults button. The Restore Factory Defaults message in Figure 5-9 appears. Figure 5-9. Restore Factory Defaults Message 3. If you want to return the management port to its default factory setting, click Yes. Doing so, however, means you will have to change the IP address of your Management Center to the same subnet as the xStack Storage's default port 192.168.1.1. Otherwise, click No to not restore the management port to the factory default setting. Or you can click Cancel to cancel the operation. xStack Storage Management Center Software User's Guide 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
xStack Storage Management Center Software User’s Guide
77
5.2.5 Restoring Factory Default Settings
There may be times when you want to return the xStack Storage system to its factory
default settings. Using the
Restore Factory Defaults
button in the
Settings
tab of the
System Administration view, you can return the xStack Storage system to the settings that
were in effect when it was shipped from the factory. However, any volumes you set up will
remain intact. For a complete list of the xStack Storage’s factory default settings, refer to
Appendix B.
1.
In the System Administration View, click the
Settings
tab to display the general settings
in Figure 5-6 on page 75. Or if you are already in the
Settings
tab but another screen is
displayed, click the
General
button on the left side of the
Settings
tab:
2.
Under
xStack Configuration
, click the
Restore Factory Defaults
button.
The Restore Factory Defaults message in Figure 5-9 appears.
Figure 5-9. Restore Factory Defaults Message
3.
If you want to return the management port to its default factory setting, click
Yes
.
Doing so, however, means you will have to change the IP address of your Management
Center to the same subnet as the xStack Storage’s default port 192.168.1.1. Otherwise,
click
No
to not restore the management port to the factory default setting. Or you can
click
Cancel
to cancel the operation.