D-Link DSS-200G-28MPP Product Manual - Page 20

DSS-200G-28MPP, Front Panel

Get D-Link DSS-200G-28MPP PDF manuals and user guides View all D-Link DSS-200G-28MPP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

D-Link DSS-200G MP/MPP series Switch User Manual DSS-200G-28MPP 24 x 10/100/1000 Mbps PoE ports + 4 x 1000BASE-T/SFP Combo ports surveillance switch Front Panel Figure 2-7 DSS-200G-28MPP Front Panel Mode Button: By pressing the Mode button over 2 seconds, the Port LED (ports 1~24) will switch between the Link (refer to the below Link/Act/Speed LED) and PoE mode to indicate the PoE ports (refer to the below PoE LED) status or link speed: PoE/Link Mode LED Description Green The Port LED indicator is in Link/Act/Speed mode. Orange The Port LED indicator is in PoE mode. Reset: The Reset button has 3 modes: Reset Mode Description Reboot Press the reset button and hold it for 1~5 seconds to reboot the device. Reset to factory default Press the reset button and hold it for longer than 5 seconds (the port LEDs should all flash orange) to reset the device to its factory defaults, which will erase all configuration changes. Reset to loader mode Press the reset button and hold it for longer than 10 seconds to enter the loader mode (the port LEDs should all flash orange and then green), which allows you to upgrade the firmware. Alert LED: The Alert indicator is blinking red to indicate PoE malfunctioning events: PoE function startup failure, PoE function disabled due to thermal abnormality, PoE power denial, PoE power 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
D-Link DSS-200G MP/MPP series Switch User Manual
15
DSS-200G-28MPP
24 x 10/100/1000 Mbps PoE ports + 4 x 1000BASE-T/SFP Combo ports surveillance switch
Front Panel
Figure 2-7 DSS-200G-28MPP Front Panel
Mode Button:
By pressing the Mode button over 2 seconds, the Port LED (ports 1~24) will switch between
the Link (refer to the below
Link/Act/Speed LED
) and PoE mode to indicate the PoE ports
(refer to the below
PoE LED
) status or link speed:
PoE/Link Mode LED
Description
Green
The Port LED indicator is in Link/Act/Speed mode.
Orange
The Port LED indicator is in PoE mode.
Reset:
The Reset button has 3 modes:
Reset Mode
Description
Reboot
Press the reset button and hold it for 1~5 seconds to reboot
the device.
Reset to factory default
Press the reset button and hold it for longer than 5 seconds
(the port LEDs should all flash orange) to reset the device
to its factory defaults, which will erase all configuration
changes.
Reset to loader mode
Press the reset button and hold it for longer than 10
seconds to enter the loader mode (the port LEDs should
all flash orange and then green), which allows you to
upgrade the firmware.
Alert LED:
The Alert indicator is blinking red to indicate PoE malfunctioning events: PoE function startup
failure, PoE function disabled due to thermal abnormality, PoE power denial, PoE power