D-Link DSS-200G-28MPP Product Manual - Page 52

HTTP/HTTPS, D-Link Discovery Protocol, Management > D-Link Discovery Protocol

Get D-Link DSS-200G-28MPP PDF manuals and user guides View all D-Link DSS-200G-28MPP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

D-Link DSS-200G MP/MPP series Switch User Manual Host IPv4 Address Enter the IPv4 address of the SNMP notification host. User-based Security Model Select the security model here. Options to choose from are SNMPv1, and SNMPv2c. SNMPv1- Select to allow the group user to use the SNMPv1 security model. SNMPv2c-Select to allow the group user to use the SNMPv2c security model. Community String Enter the community string to be sent with the notification packet. Click the Apply button to accept the changes made. Click the Clear button to remove SNMP Host. HTTP/HTTPS This window is used to configure Web settings on the switch. To view the following window, click Management > HTTP/HTTPS, as shown below: Figure 4-27 HTTP/HTTPS window The fields that can be configured for HTTP/HTTPS Settings are described below: Parameter Web Session Description Select this option to enable the configuration through HTTP or HTTPS. Note: When switching from HTTP to HTTPS mode, the switch will take about 30 seconds to initialize the secured HTTP environment. Web Session Timeout (60- Enter a value for the amount of time in seconds before the web 36000) session expires. Click the Apply button to accept the changes made. Note: If the switch is in HTTPS mode, the firmware or configuration cannot be upgraded using regular HTTP. D-Link Discovery Protocol This window is used to configure and display D-Link Discovery Protocol (DDP). To view the following window, click Management > D-Link Discovery Protocol, as shown below: 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
D-Link DSS-200G MP/MPP series Switch User Manual
47
Host IPv4 Address
Enter the IPv4 address of the SNMP notification host.
User-based Security Model
Select the security model here. Options to choose from are
SNMPv1
, and
SNMPv2c
.
SNMPv1
- Select to allow the group user to use the SNMPv1
security model.
SNMPv2c
-Select to allow the group user to use the SNMPv2c
security model.
Community String
Enter the community string to be sent with the notification
packet.
Click the
Apply
button to accept the changes made.
Click the
Clear
button to remove SNMP Host.
HTTP/HTTPS
This window is used to configure Web settings on the switch.
To view the following window, click
Management > HTTP/HTTPS
, as shown below:
Figure 4-27 HTTP/HTTPS window
The fields that can be configured for
HTTP/HTTPS Settings
are described below:
Parameter
Description
Web Session
Select this option to enable the configuration through HTTP or
HTTPS.
Note:
When switching from HTTP to HTTPS mode, the switch
will take about 30 seconds to initialize the secured HTTP
environment.
Web Session Timeout (60-
36000)
Enter a value for the amount of time in seconds before the web
session expires.
Click the
Apply
button to accept the changes made.
Note
: If the switch is in HTTPS mode, the firmware or configuration cannot be upgraded using regular
HTTP.
D-Link Discovery Protocol
This window is used to configure and display D-Link Discovery Protocol (DDP).
To view the following window, click
Management > D-Link Discovery Protocol
, as shown below: