D-Link DSS-200G-28MPP Product Manual - Page 38

Port Configuration, Port Settings

Get D-Link DSS-200G-28MPP PDF manuals and user guides View all D-Link DSS-200G-28MPP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

D-Link DSS-200G MP/MPP series Switch User Manual Port Configuration Port Settings This window is used to view and configure the switch's port settings. To view the following window, click System > Port Configuration > Port Settings, as shown below: Figure 4-10 Port Settings window Note: Ports are that support PoE Extent cannot be configured if the Dip Switch on the front panel has been turned on. The fields that can be configured are described below: Parameter From Port / To Port Medium Type State MDIX Flow Control Duplex Speed Description Description Select the appropriate port range used for the configuration here. Select the port type to RJ45 or SFP. Select this option to enable or disable the physical port here. Select the Medium Dependent Interface Crossover (MDIX) option here. Options to choose from are Auto, Normal, and Cross. Auto - Select this option for auto-sensing of the optimal type of cabling. Normal - Select this option for normal cabling. If this option is selected, the port is in the MDIX mode and can be connected to a PC's NIC using a straight-through cable or a port (in the MDIX mode) on another switch through a cross-over cable. Cross - Select this option for cross cabling. If this option is selected, the port is in the MDI mode and can be connected to a port (in the MDIX mode) on another switch through a straight cable. Select to either turn flow control On or Off here. Ports configured for full-duplex use 802.3x flow control, half-duplex ports use back-pressure flow control, and Auto ports use an automatic selection of the two. Select the duplex mode used here. Options to choose from are Auto, Half, and Full. Select the port speed option here. This option will manually force the connected on the selected port to only connect at the speed specified here. Options to choose from are Auto, 10M, 100M. 1000M speed is only available when Auto is selected. Enter a 8 characters description for the corresponding port here. Click the Apply button to accept the changes made. Note: The SFP ports on the DSS-200G MP/MPP series only support Auto for duplex and speed. Also, the fiber ports on the DSS-200G MP/MPP series does not support MDIX. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
D-Link DSS-200G MP/MPP series Switch User Manual
33
Port Configuration
Port Settings
This window is used to view and configure the switch’s port settings.
To view the following window, click
System > Port Configuration > Port Settings
, as shown below:
Figure 4-10 Port Settings window
Note:
Ports are that support PoE Extent cannot be configured if the Dip Switch on the front panel has
been turned on.
The fields that can be configured are described below:
Parameter
Description
From Port / To Port
Select the appropriate port range used for the configuration
here.
Medium Type
Select the port type to RJ45 or SFP.
State
Select this option to
enable
or
disable
the physical port here.
MDIX
Select the Medium Dependent Interface Crossover (MDIX)
option here. Options to choose from are
Auto
,
Normal
, and
Cross
.
Auto
- Select this option for auto-sensing of the optimal type
of cabling.
Normal
- Select this option for normal cabling. If this option is
selected, the port is in the MDIX mode and can be connected
to a PC’s NIC using a straight
-through cable or a port (in the
MDIX mode) on another switch through a cross-over cable.
Cross
- Select this option for cross cabling. If this option is
selected, the port is in the MDI mode and can be connected
to a port (in the MDIX mode) on another switch through a
straight cable.
Flow Control
Select to either turn flow control
On
or
Off
here. Ports
configured for full-duplex use 802.3x flow control, half-duplex
ports use back-pressure flow control, and Auto ports use an
automatic selection of the two.
Duplex
Select the duplex mode used here. Options to choose from
are
Auto
,
Half
, and
Full
.
Speed
Select the port speed option here. This option will manually
force the connected on the selected port to only connect at the
speed specified here. Options to choose from are
Auto
,
10M
,
100M
.
1000M
speed is only available when
Auto
is selected.
Description
Enter a 8 characters description for the corresponding port
here.
Click the
Apply
button to accept the changes made.
Note
: The SFP ports on the DSS-200G MP/MPP series only support
Auto
for duplex and speed. Also,
the fiber ports on the DSS-200G MP/MPP series does not support MDIX.