Dell Force10 C300 C300 Hardware Installation Guide - Page 54

To con the chassis from the BOOT_USER prompt, use the following commands, boot change

Get Dell Force10 C300 PDF manuals and user guides View all Dell Force10 C300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

www.dell.com | support.dell.com To configure the chassis from the BOOT_USER prompt, use the following commands: Command help or ? boot change {primary | secondary | default} show bootvar show bootflash interface management port config 100m interface management port config 10m interface management port config auto-negotiate interface management port config no auto-negotiate interface management port config full-duplex interface management port config half-duplex interface management port config show Purpose • Enter help or ? to display a list of available commands and syntax. • Enter syntax help t display syntax information and variable descriptions. If your configuration displays no pre-configured operating system boot parameters, use the boot change command to edit appropriate fields. • The primary operating system boot parameters are used in the first attempt to boot the system. • The secondary operating system boot parameters are used if the primary operating system boot selection is not available. • The default operating system boot parameters are used if the secondary operating system boot parameter is not available. The default parameters always reside on the internal flash drive (flash). NOTE: These parameters, as well as other boot parameters, can be modified in run-time mode When you enter the boot change command, you are prompted for a response. • Enter a new parameter or press the ENTER key (carriage return) to accept the default parameter. • Enter . (period) to clear a field. • Enter - (dash) to edit a field above the current cursor position. NOTE: When you enter a new parameter that extends beyond 80 characters, you cannot use the BACKSPACE key to correct any mistakes. If you make a mistake, you must re-enter the parameter. This command displays the current operating system boot configuration parameters This command displays information about the current boot ROM. • Use these commands to set the speed and duplex settings for the Management interface. The default setting is full-duplex and autonegotiation. • Use the interface management port config show command to view the management interface's physical settings. 54 | System Boot

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
54
|
System Boot
www.dell.com | support.dell.com
To configure the chassis from the BOOT_USER prompt, use the following commands:
Command
Purpose
help
or
?
• Enter
help
or
?
to display a list of available commands and syntax.
• Enter
syntax help
t display syntax information and variable descriptions.
boot change
{
primary
|
secondary
|
default
}
If your configuration displays no pre-configured operating system boot
parameters, use the
boot change
command to edit appropriate fields.
• The
primary
operating system boot parameters are used in the first attempt
to boot the system.
• The
secondary
operating system boot parameters are used if the primary
operating system boot selection is not available.
• The
default
operating system boot parameters are used if the secondary
operating system boot parameter is not available. The default parameters
always reside on the internal flash drive (flash).
NOTE:
These parameters, as well as other boot parameters, can be
modified in run-time mode
When you enter the boot change command, you are prompted for a response.
•
Enter a new parameter or press the ENTER key (carriage return) to accept
the default parameter.
• Enter
.
(period) to clear a field.
• Enter
-
(dash) to edit a field above the current cursor position.
NOTE:
When you enter a new parameter that extends beyond 80
characters, you cannot use the BACKSPACE key to correct any mistakes. If
you make a mistake, you must re-enter the parameter.
show bootvar
This command displays the current operating system boot configuration
parameters
show bootflash
This command displays information about the current boot ROM.
interface management port config
100m
interface management port config
10m
interface management port config
auto-negotiate
interface management port config
no auto-negotiate
interface management port config
full-duplex
interface management port config
half-duplex
interface management port config
show
•
Use these commands to set the speed and duplex settings for the
Management interface. The default setting is full-duplex and auto-
negotiation.
•
Use the
interface management port config show
command to view
the management interface’s physical settings.