Dell Inspiron 16 7630 2-in-1 Service Manual - Page 21

Solid-state drive, Removing the M.2 2230 solid-state drive

Get Dell Inspiron 16 7630 2-in-1 PDF manuals and user guides View all Dell Inspiron 16 7630 2-in-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Steps 1. Using the alignment posts, place the battery on the palm-rest and keyboard assembly. 2. Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly. 3. Replace the six screws (M2x3.5) that secure the battery to the palm-rest and keyboard assembly. 4. Connect the battery cable to the system board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Solid-state drive Removing the M.2 2230 solid-state drive Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. About this task NOTE: This procedure applies only to computers shipped with an M.2 2230 solid-state drive installed. NOTE: The M.2 card installed will depend on the configuration ordered. Supported card configurations on the M.2 card slot: ● M.2 2230 solid-state drive + M.2 2230 mounting bracket ● M.2 2280 solid-state drive The following image(s) indicate the location of the M.2 2230 solid-state drive and provides a visual representation of the removal procedure. Removing and installing components 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
Steps
1.
Using the alignment posts, place the battery on the palm-rest and keyboard assembly.
2.
Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.
3.
Replace the six screws (M2x3.5) that secure the battery to the palm-rest and keyboard assembly.
4.
Connect the battery cable to the system board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Solid-state drive
Removing the M.2 2230 solid-state drive
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
About this task
NOTE:
This procedure applies only to computers shipped with an M.2 2230 solid-state drive installed.
NOTE:
The M.2 card installed will depend on the configuration ordered. Supported card configurations on the M.2 card slot:
●
M.2 2230 solid-state drive + M.2 2230 mounting bracket
●
M.2 2280 solid-state drive
The following image(s) indicate the location of the M.2 2230 solid-state drive and provides a visual representation of the
removal procedure.
Removing and installing components
21