Dell Inspiron 16 Plus 7630 Owners Manual- NVIDIA GeForce RTX 4060 - Page 40

Solid-state drive, Removing the M.2 2230 solid-state drive

Get Dell Inspiron 16 Plus 7630 PDF manuals and user guides View all Dell Inspiron 16 Plus 7630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Steps 1. Connect the battery cable to its connector on the system board. 2. Place the base cover on the palm-rest and keyboard assembly. 3. Press on the sides of the base cover to snap it into place. 4. Tighten the two captive screws that secure the base cover to the palm-rest and keyboard assembly. 5. Replace the seven screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly. Next steps 1. Follow the procedure in After working inside your computer. Solid-state drive Removing the M.2 2230 solid-state drive Prerequisites 1. Follow the procedure in Before working inside your computer. NOTE: Ensure that your computer is in Service Mode. For more information see, step 6 in Before working inside your computer. 2. Remove the base cover. About this task NOTE: This procedure applies only to computers shipped with an M.2 2230 solid-state drive installed. NOTE: A mounting bracket for the M.2 2230 solid-state drive is required. The mounting bracket is provided if the M.2 2230 solid-state is shipped with the computer. NOTE: The M.2 solid-state drive installed on your computer depends on the configuration ordered. The M.2 slot supports one of the following solid-state drives: ● M.2 2230 solid-state drive 40 Removing and installing Customer Replaceable Units (CRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Steps
1.
Connect the battery cable to its connector on the system board.
2.
Place the base cover on the palm-rest and keyboard assembly.
3.
Press on the sides of the base cover to snap it into place.
4.
Tighten the two captive screws that secure the base cover to the palm-rest and keyboard assembly.
5.
Replace the seven screws (M2x4) that secure the base cover to the palm-rest and keyboard assembly.
Next steps
1.
Follow the procedure in
After working inside your computer
.
Solid-state drive
Removing the M.2 2230 solid-state drive
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
NOTE:
Ensure that your computer is in Service Mode. For more information see, step 6 in
Before working inside your
computer
.
2.
Remove the
base cover
.
About this task
NOTE:
This procedure applies only to computers shipped with an M.2 2230 solid-state drive installed.
NOTE:
A mounting bracket for the M.2 2230 solid-state drive is required. The mounting bracket is provided if the M.2 2230
solid-state is shipped with the computer.
NOTE:
The M.2 solid-state drive installed on your computer depends on the configuration ordered. The M.2 slot supports
one of the following solid-state drives:
●
M.2 2230 solid-state drive
40
Removing and installing Customer Replaceable Units (CRUs)