Dell Inspiron 16 Plus 7630 Owners Manual- NVIDIA GeForce RTX 4060 - Page 71

System board, Removing the system board

Get Dell Inspiron 16 Plus 7630 PDF manuals and user guides View all Dell Inspiron 16 Plus 7630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Steps 1. Place the power button with optional fingerprint reader on the palm-rest and keyboard assembly. 2. Align the screw hole on the power button with optional fingerprint reader with the screw hole on the palm-rest and keyboard assembly. 3. Replace the screw (M2x2) that secures the power button with optional fingerprint reader to the palm-rest and keyboard assembly. 4. Connect the fingerprint-reader cable to its connector on the I/O board and close the latch. NOTE: Steps 4, 5 and 6 are only applicable for systems shipped with a fingerprint reader. 5. Adhere the fingerprint-reader cable to the palm-rest and keyboard assembly. 6. Replace the Mylar over the fingerprint-reader cable. Next steps 1. Install the power-button board. 2. Install the heat sink. 3. Install the left fan. 4. Install the base cover. 5. Follow the procedure in After working inside your computer. System board Removing the system board CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. NOTE: Ensure that your computer is in Service Mode. For more information see, step 6 in Before working inside your computer. 2. Remove the base cover. 3. Remove the memory module. 4. Remove the M.2 2230 solid-state drive or M.2 2280 solid-state drive, whichever applicable. Removing and installing Field Replaceable Units (FRUs) 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
Steps
1.
Place the power button with optional fingerprint reader on the palm-rest and keyboard assembly.
2.
Align the screw hole on the power button with optional fingerprint reader with the screw hole on the palm-rest and keyboard
assembly.
3.
Replace the screw (M2x2) that secures the power button with optional fingerprint reader to the palm-rest and keyboard
assembly.
4.
Connect the fingerprint-reader cable to its connector on the I/O board and close the latch.
NOTE:
Steps 4, 5 and 6 are only applicable for systems shipped with a fingerprint reader.
5.
Adhere the fingerprint-reader cable to the palm-rest and keyboard assembly.
6.
Replace the Mylar over the fingerprint-reader cable.
Next steps
1.
Install the
power-button board
.
2.
Install the
heat sink
.
3.
Install the
left fan
.
4.
Install the
base cover
.
5.
Follow the procedure in
After working inside your computer
.
System board
Removing the system board
CAUTION:
The information in this section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
NOTE:
Ensure that your computer is in Service Mode. For more information see, step 6 in
Before working inside your
computer
.
2.
Remove the
base cover
.
3.
Remove the
memory module
.
4.
Remove the
M.2 2230 solid-state drive
or
M.2 2280 solid-state drive
, whichever applicable.
Removing and installing Field Replaceable Units (FRUs)
71