Dell OptiPlex 3046 Small Form Factor Owners Manual - Page 35

Option, Description, Auto Power is set to disabled, Disabled, LAN Only, LAN with PXE Boot

Get Dell OptiPlex 3046 Small Form Factor PDF manuals and user guides View all Dell OptiPlex 3046 Small Form Factor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Option Limited CPUID Value Intel TurboBoost HyperThread control Description Allows you to limit the maximum value of the processor standard CPUID function. This options is disable by default. Allows you to enable or disable the Intel TurboBoost mode of the processor. This option is enabled by default. Allows you to enable or disable HyperThreading in the processor. Table 11. Power management Option AC Recovery Auto On Time Deep Sleep Control Fan Control Override USB Wake Support Wake on LAN/WWAN Block Sleep Intel Ready Mode Description Determines how the system responds when AC power is re-applied after a power loss. You can set the AC Recovery to: • Power Off • Power On • Last Power State This option is Power Off by default. Sets time to automatically turn on the computer. Time is kept in standard 12-hour format (hour:minutes:seconds). Change the startup time by typing the values in the time and AM/PM fields. NOTE: This feature does not work if you turn off your computer using the switch on a power strip or surge protector or if Auto Power is set to disabled. Allows you to define the controls when Deep Sleep is enabled. • Disabled • Enabled in S5 only • Enabled in S4 and S5 This option is Disabled by default. Allows you to determine the speed of the system fan. When this option is enabled, the system fan runs at the maximum speed. This option is disabled by default. Allows you to enable the USB devices to wake the computer from standby mode. This option allows the computer to power up from the off state when triggered by a special LAN signal. This feature only works when the computer is connected to AC power supply. • Disabled - Does not allows the system to power on by special LAN signals when it receives a wake-up signal from the LAN or wireless LAN. • LAN or WLAN - Allows the system to be powered on by special LAN or wireless LAN signals. • LAN Only - Allows the system to be powered on by special LAN signals. • LAN with PXE Boot - A wakeup packet sent to the system in either the S4 or S5 state, that will cause the system to wake-up and immediately boot to PXE. • WLAN Only - Allows the system to be powered on by special WLAN signals. This option is Disabled by default. Allows you to block entering to sleep (S3 state) in OS environment. This option is disabled by default. Allows you to enable the capability of Intel Ready Mode Technology. This option is disabled by default. System Setup 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
Option
Description
Limited CPUID Value
Allows you to limit the maximum value of the processor standard CPUID function. This
options is disable by default.
Intel TurboBoost
Allows you to enable or disable the Intel TurboBoost mode of the processor. This option is
enabled by default.
HyperThread control
Allows you to enable or disable HyperThreading in the processor.
Table 11. Power management
Option
Description
AC Recovery
Determines how the system responds when AC power is re-applied after a power loss. You
can set the AC Recovery to:
•
Power Off
•
Power On
•
Last Power State
This option is Power Off by default.
Auto On Time
Sets time to automatically turn on the computer. Time is kept in standard 12-hour format
(hour:minutes:seconds). Change the startup time by typing the values in the time and
AM/PM fields.
NOTE:
This feature does not work if you turn off your computer using the switch on a
power strip or surge protector or if
Auto Power is set to disabled
.
Deep Sleep Control
Allows you to define the controls when Deep Sleep is enabled.
•
Disabled
•
Enabled in S5 only
•
Enabled in S4 and S5
This option is Disabled by default.
Fan Control Override
Allows you to determine the speed of the system fan. When this option is enabled, the
system fan runs at the maximum speed. This option is disabled by default.
USB Wake Support
Allows you to enable the USB devices to wake the computer from standby mode.
Wake on LAN/WWAN
This option allows the computer to power up from the off state when triggered by a special
LAN signal. This feature only works when the computer is connected to AC power supply.
•
Disabled
- Does not allows the system to power on by special LAN signals when it
receives a wake-up signal from the LAN or wireless LAN.
•
LAN
or
WLAN
- Allows the system to be powered on by special LAN or wireless LAN
signals.
•
LAN Only
- Allows the system to be powered on by special LAN signals.
•
LAN with PXE Boot
- A wakeup packet sent to the system in either the S4 or S5 state,
that will cause the system to wake-up and immediately boot to PXE.
•
WLAN Only
- Allows the system to be powered on by special WLAN signals.
This option is Disabled by default.
Block Sleep
Allows you to block entering to sleep (S3 state) in OS environment. This option is disabled by
default.
Intel Ready Mode
Allows you to enable the capability of Intel Ready Mode Technology. This option is disabled
by default.
System Setup
35