Dell PowerConnect M6220 Configuration Guide - Page 28

Web Interface, IP Subnet and MAC-Based VLANs, CLI Examples, Switching > VLAN > Membership

Get Dell PowerConnect M6220 PDF manuals and user guides View all Dell PowerConnect M6220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Example #5: Assign IP Addresses to VLAN 2 In order for the VLAN to function as a routing interface, you must enable routing on the VLAN and on the switch. Routing is only permitted on VLAN interfaces. Routing on physical interfaces is not supported. console#configure console(config)#interface vlan 2 console(config-if-vlan2)#ip address 192.168.10.33 255.255.255.0 console(config-if-vlan2)#routing console(config-if-vlan2)#exit console(config)#ip routing Example #6: View Information About VLAN 2 console#show ip interface vlan 2 Primary IP Address 192.168.10.33/255.255.255.0 Routing Mode Enable Administrative Mode Enable Forward Net Directed Broadcasts Disable Proxy ARP Enable Local Proxy ARP Disable Active State Inactive Link Speed Data Rate 10 Half MAC Address 00FF.F2A3.888A Encapsulation Type Ethernet IP MTU 1500 Web Interface Use the following screens to perform the same configuration using the Web Interface: • Switching > VLAN > Membership. To create VLANs and specify port participation. • Switching > VLAN > Port Settings. To specify the PVID and mode for the port. IP Subnet and MAC-Based VLANs In addition to port-based VLANs, the switch also supports VLANs that are based on the IP address or MAC address of a host. With IP subnet and MAC-based VLANs, the VLAN membership is determined by the address of the host rather than the port to which the host is attached. CLI Examples The following examples show how to associate an IP subnet with a VLAN, a specific IP address with a VLAN, and a MAC address with a VLAN. 28 Switching Configuration

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
28
Switching Configuration
Example #5: Assign IP Addresses to VLAN 2
In order for the VLAN to function as a routing interface, you must enable routing on the VLAN and on
the switch. Routing is only permitted on VLAN interfaces. Routing on physical interfaces is not
supported.
console#configure
console(config)#interface vlan 2
console(config-if-vlan2)#ip address 192.168.10.33 255.255.255.0
console(config-if-vlan2)#routing
console(config-if-vlan2)#exit
console(config)#ip routing
Example #6: View Information About VLAN 2
console#show ip interface vlan 2
Primary IP Address
............................
192.168.10.33/255.255.255.0
Routing Mode
..................................
Enable
Administrative Mode
...........................
Enable
Forward Net Directed Broadcasts
...............
Disable
Proxy ARP
.....................................
Enable
Local Proxy ARP
...............................
Disable
Active State
..................................
Inactive
Link Speed Data Rate
..........................
10 Half
MAC Address
...................................
00FF.F2A3.888A
Encapsulation Type
............................
Ethernet
IP MTU
........................................
1500
Web Interface
Use the following screens to perform the same configuration using the Web Interface:
•
Switching > VLAN > Membership
. To create VLANs and specify port participation.
•
Switching > VLAN > Port Settings.
To specify the PVID and mode for the port.
IP Subnet and MAC-Based VLANs
In addition to port-based VLANs, the switch also supports VLANs that are based on the IP address or
MAC address of a host. With IP subnet and MAC-based VLANs, the VLAN membership is determined
by the address of the host rather than the port to which the host is attached.
CLI Examples
The following examples show how to associate an IP subnet with a VLAN, a specific IP address with a
VLAN, and a MAC address with a VLAN.