Dell PowerConnect M6220 Configuration Guide - Page 51

Example #7: Con Group Full/Half Duplex Operation of All Member Ports

Get Dell PowerConnect M6220 PDF manuals and user guides View all Dell PowerConnect M6220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Example #7: Configure Group Full/Half Duplex Operation of All Member Ports Use the duplex command in port aggregator configuration mode to configure the full/half duplex operation of all member ports in the aggregator group. The example command below configures all member ports to full duplex operation. console(config)#port-aggregator group 1 console(config-aggregator-1)#duplex full console(config-aggregator-1)# Example #8: Set Group LACP Mode to Static Use the lacp static command to set the LACP (Link Aggregation) mode to static for that Aggregator Group. This means that when more than one uplink port is in the Group, those uplink ports will be enabled automatically and will not use LACP. console(config)#port-aggregator group 2 console(config-aggregator-2)#lacp static console(config-aggregator-2)# Example #9: Set Group LACP Mode to Dynamic Use the lacp auto command to set the LACP (Link Aggregation) mode to dynamic for that Aggregator Group. This means that when more than one uplink port is in the Group, those uplink ports will be enabled automatically with LACP. console(config)#port-aggregator group 2 console(config-aggregator-2)#lacp auto console(config-aggregator-2)# Example #10: Set Group LACP Mode Use the lacp off command to set the LACP (Link Aggregation) mode to off for that Aggregator Group. This means that when more than one uplink port is in the Group, all the uplinks are shut down except the lowest numbered one. console(config)#port-aggregator group 2 console(config-aggregator-2)#lacp off console(config-aggregator-2)# Example #11: Set Minimum Active Uplinks Use the minimum active uplinks command to set the minimum number of uplinks to be active for the Group. For example, if the number of uplink ports in the group is 2 and the number of internal ports is 4. If the user sets the minimum active uplink ports to be 2, then both the Switching Configuration 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Switching Configuration
51
Example #7: Configure Group Full/Half Duplex Operation of All Member Ports
Use the
duplex
command in port aggregator configuration mode to configure the full/half duplex
operation of all member ports in the aggregator group. The example command below configures all
member ports to full duplex operation.
console(config)#port-aggregator group 1
console(config-aggregator-1)#duplex full
console(config-aggregator-1)#
Example #8: Set Group LACP Mode to Static
Use the
lacp static
command to set the LACP (Link Aggregation) mode to static for that Aggregator
Group. This means that when more than one uplink port is in the Group, those uplink ports will be
enabled automatically and will not use LACP.
console(config)#port-aggregator group 2
console(config-aggregator-2)#lacp static
console(config-aggregator-2)#
Example #9: Set Group LACP Mode to Dynamic
Use the
lacp auto
command to set the LACP (Link Aggregation) mode to dynamic for that Aggregator
Group. This means that when more than one uplink port is in the Group, those uplink ports will be
enabled automatically with LACP.
console(config)#port-aggregator group 2
console(config-aggregator-2)#lacp auto
console(config-aggregator-2)#
Example #10: Set Group LACP Mode
Use the
lacp off
command to set the LACP (Link Aggregation) mode to off for that Aggregator Group.
This means that when more than one uplink port is in the Group, all the uplinks are shut down except
the lowest numbered one.
console(config)#port-aggregator group 2
console(config-aggregator-2)#lacp off
console(config-aggregator-2)#
Example #11: Set Minimum Active Uplinks
Use the
minimum active uplinks <number of uplinks>
command to set the minimum number of
uplinks to be active for the Group. For example, if the number of uplink ports in the group is 2 and the
number of internal ports is 4. If the user sets the minimum active uplink ports to be 2, then both the