Dell Precision 330 Service Manual - Page 88

Disconnect the DC power and interface cables from the back of the, away from the system board.

Get Dell Precision 330 PDF manuals and user guides View all Dell Precision 330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

www.dell.com | support.dell.com NOTICE: Before disconnecting a peripheral from the system or removing a component from the system board, verify that the standby power indicator on the system board has turned off. To locate this indicator, see "System Board Components" or "Interior Service Label." 1 Turn off the computer and peripherals, disconnect them from their electrical outlets, wait at least 5 seconds, and then remove the computer cover. 2 Rotate the power supply away from the system board. 3 Remove the front panel. 4 Disconnect the DC power and interface cables from the back of the drive. 5 Remove the drive bracket from the chassis. Pull the drive door forward and down until the hard-drive bracket is ejected halfway out of the chassis (see the following figure). Then grasp the bracket and pull it completely out of the chassis. 88 Disk Dri ves and Media

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
88
Disk Drives and Media
www.dell.com | support.dell.com
NOTICE:
Before disconnecting a peripheral from the system or removing a
component from the system board, verify that the standby power indicator on
the system board has turned off. To locate this indicator, see "
System Board
Components
" or "
Interior Service Label
."
1
Turn off the computer and peripherals, disconnect them from their
electrical outlets, wait at least 5 seconds, and then
remove the
computer cover
.
2
Rotate the power supply
away from the system board.
3
Remove the front panel
.
4
Disconnect the DC power and interface cables from the back of the
drive.
5
Remove the drive bracket from the chassis.
Pull the drive door forward and down until the hard-drive bracket is
ejected halfway out of the chassis (see the following figure). Then
grasp the bracket and pull it completely out of the chassis.