Dell S4148U-ON EMC Networking FCoE Deployment with S4148U-ON in NPG Mode - Page 13

S4148U-ON switch configuration

Get Dell S4148U-ON PDF manuals and user guides View all Dell S4148U-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

5 S4148U-ON switch configuration This section details steps to configure the S4148U-ON leaf switches running OS10EE. 5.1 Prepare switches 5.1.1 Factory default configuration The configuration commands in the sections that follow begin with S4148U-ON switches at their factory default settings. Dell EMC PowerSwitch models running OS10EE can be reset to their default configuration as follows: OS10# delete startup-configuration Proceed to delete startup-configuration [confirm yes/no(default)]:y OS10# reload System configuration has been modified. Save? [yes/no]:n Proceed to reboot the system? [confirm yes/no]:y The switch reboots to its factory default configuration. Repeat on the second S4148U-ON switch. Note: OS10EE at its default settings has Telnet disabled, SSH enabled, and the OOB management interface configured to get its IP address via DHCP. The default username and password are both admin. Dell EMC recommends changing the admin password to a complex password during the first login. 5.1.2 Set switch port profile A switch port profile determines the enabled front-panel ports and supported breakout modes on Ethernet and unified ports. Changing the profile removes the existing switch configuration, so the switch port profile is configured first. Switch port profile-3 is used in this deployment to enable four 100GbE ports on each S4148U-ON for the leaf-spine portion of the topology. This profile also provides twelve 16Gb FC ports for storage connections. Note: See OS10 Enterprise Edition User Guide Release 10.4.2.0 for switch-port profile options and details. To change the switch-port profile from its current setting: OS10# configure terminal OS10(config)# switch-port-profile 1/1 profile-3 Warning: Switch port profile will be applied only after a save and reload. All management port configurations will be retained but all other configurations will be wiped out after the reload. OS10(config)# exit OS10# write memory OS10# reload Proceed to reboot the system? [confirm yes/no]:y 13 Dell EMC Networking FCoE Deployment with S4148U-ON in NPG Mode

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
13
Dell EMC Networking FCoE Deployment with S4148U-ON in NPG Mode
5
S4148U-ON switch configuration
This section details steps to configure the S4148U-ON leaf switches running OS10EE.
5.1
Prepare switches
5.1.1
Factory default configuration
The configuration commands in the sections that follow begin with S4148U-ON switches at their factory
default settings. Dell EMC PowerSwitch models running OS10EE can be reset to their default configuration as
follows:
OS10#
delete startup-configuration
Proceed to delete startup-configuration [confirm yes/no(default)]:
y
OS10#
reload
System configuration has been modified. Save? [yes/no]:
n
Proceed to reboot the system? [confirm yes/no]:
y
The switch reboots to its factory default configuration. Repeat on the second S4148U-ON switch.
Note:
OS10EE at its default settings has Telnet disabled, SSH enabled, and the OOB management interface
configured to get its IP address via DHCP. The default username and password are both admin. Dell EMC
recommends changing the admin password to a complex password during the first login.
5.1.2
Set switch port profile
A switch port profile determines the enabled front-panel ports and supported breakout modes on Ethernet and
unified ports. Changing the profile removes the existing switch configuration, so the switch port profile is
configured first. Switch port profile-3 is used in this deployment to enable four 100GbE ports on each
S4148U-ON for the leaf-spine portion of the topology. This profile also provides twelve 16Gb FC ports for
storage connections.
Note:
See
OS10 Enterprise Edition User Guide Release 10.4.2.0
for switch-port profile options and details.
To change the switch-port profile from its current setting:
OS10#
configure terminal
OS10(config)#
switch-port-profile 1/1 profile-3
Warning: Switch port profile will be applied only after a save and reload.
All management port configurations will be retained but all other
configurations will be wiped out after the reload.
OS10(config)#
exit
OS10#
write memory
OS10#
reload
Proceed to reboot the system? [confirm yes/no]:
y