Dell W-7205 Controller Installation Guide - Page 15

USB Interface, Serial Console Port, Table 8,

Get Dell W-7205 PDF manuals and user guides View all Dell W-7205 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Table 8: Supported SFP/SFP+ Modules SFP/SFP+ Description SFP-10G-ER SFP+, 10GBASE-ER, 1310nm pluggable 10GE optic; up to 40,000 meters over single-mode fiber, LC connector SFP-10G-ZR SFP+, 10GBASE-ZR, 1310nm pluggable 10GE optic; up to 70,000 meters over single-mode fiber, LC connector Table 9: Supported DAC Cables DAC DAC-SFP-10GE-50CM DAC-SFP-10GE-1M DAC-SFP-10GE-3M DAC-SFP-10GE-5M DAC-SFP-10GE-7M Description 50cm Direct Attach Cable; 10G SFP+ 1m Direct Attach Cable; 10G SFP+ 3m Direct Attach Cable; 10G SFP+ 5m Direct Attach Cable; 10G SFP+ 7m Direct Attach Cable; 10G SFP+ USB Interface The W-7205 controller is equipped with two USB 2.0 interfaces; one on the front panel of the controller and the other on the CPU module in the back panel of the controller. A USB storage device can be used to save configurations, upload configurations, and upgrade image to the controller. USB functions are controlled through the LCD panel on the front of the controller. For more information on the LCD panel and its functions, see "LCD Panel" on page 17. Serial Console Port For direct local management of the controller, use the serial console port located on the front (see Figure 5). This port is an RJ-45 female connector that accepts an RS-232 serial cable with a male connector. Figure 5 Serial Console Port Pin-Out Serial Console Port RJ-45 Female Pin-Out 1 2 3 4 5 6 7 8 Direction Input Output TxD GND GND RxD The communication settings for the console port are shown in the following table: Table 10: Console Terminal Settings Baud Rate Data Bits 9600 8 Parity None Stop Bits 1 Flow Control None Dell Networking W-7205 Controller | Installation Guide W-7205 Controller | 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
SFP/SFP+
Description
SFP-10G-ER
SFP+, 10GBASE-ER, 1310nm pluggable 10GE optic; up to 40,000 meters over single-mode fiber, LC connector
SFP-10G-ZR
SFP+, 10GBASE-ZR, 1310nm pluggable 10GE optic; up to 70,000 meters over single-mode fiber, LC connector
Table 8:
Supported SFP/SFP+ Modules
DAC
Description
DAC-SFP-10GE-50CM
50cm Direct Attach Cable; 10G SFP+
DAC-SFP-10GE-1M
1m Direct Attach Cable; 10G SFP+
DAC-SFP-10GE-3M
3m Direct Attach Cable; 10G SFP+
DAC-SFP-10GE-5M
5m Direct Attach Cable; 10G SFP+
DAC-SFP-10GE-7M
7m Direct Attach Cable; 10G SFP+
Table 9:
Supported DAC Cables
USB Interface
The W-7205 controller is equipped with two USB 2.0 interfaces; one on the front panel of the controller and the
other on the CPU module in the back panel of the controller. A USB storage device can be used to save
configurations, upload configurations, and upgrade image to the controller. USB functions are controlled through the
LCD panel on the front of the controller. For more information on the LCD panel and its functions, see
"LCD
Panel" on page 17
.
Serial Console Port
For direct local management of the controller, use the serial console port located on the front (see
Figure 5
). This
port is an RJ-45 female connector that accepts an RS-232 serial cable with a male connector.
Figure 5
Serial Console Port Pin-Out
Serial
Console Port
1
2
3
4
5
6
7
8
TxD
GND
RxD
RJ-45 Female
Pin-Out
Direction
Input
Output
GND
The communication settings for the console port are shown in the following table:
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
9600
8
None
1
None
Table 10:
Console Terminal Settings
Dell Networking W-7205 Controller
|
Installation Guide
W-7205 Controller
|
15