Epson TM-m30II Technical Reference Guide TM-m30II - Page 68

Auto re-connect to iOS device, model, Security Settings, the roll paper cover.

Get Epson TM-m30II PDF manuals and user guides View all Epson TM-m30II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Chapter 3 Advanced Usage Auto re-connect to iOS device (Bluetooth model) In Bluetooth model, select [Bluetooth Setup] and then select [Auto Re-Connect iOS], you can select whether to enable or disable auto reconnection to iOS devices. • For details on the auto re-connect function, see "Auto Reconnect Feature" on page 109. • You can change the settings with TM-m30II Utility and TM Utility for iOS. Bluetooth Security Settings (Bluetooth model) For Bluetooth models, select [Bluetooth Setup], and then select [Security], and you can change the Bluetooth security settings. When the security settings are changed from "Middle" or "Low" to "High", or vice versa, the link key (pairing information) is deleted. If the printer is already paired with a terminal, unpair them and then pair again. You can change the settings with TM-m30II Utility and TM Utility for iOS/Android. Security Low Middle (initial setting) High Pairing Mode Pairing Method Pairing is always possible Just Works Pairing is possible for one minute after turning the printer on Just Works or after printing the status sheet Pairing is possible for one minute after printing the status Numeric Comparison/Passkey Entry sheet Pairing method when the security is set to Middle/High (from the printer) When the security is set to Middle/High and the printer is ready to be paired, perform the following procedure. 1 Load paper in the printer, and then turn it on. • Make sure no errors have occurred and that the printer is not off-line. • You cannot pair the printer while the network is starting up immediately after the power is turned on. 2 Open the roll paper cover, hold down the FEED button (two seconds), and then close the roll paper cover. 3 A status sheet is printed, and the Bluetooth LED flashes a pattern indicating that pairing is now possible. • Pairing is possible for one minute after printing the status sheet. • You can enable pairing also by printing the status sheet by pressing the status sheet button. 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
68
Chapter 3
Advanced Usage
Auto re-connect to iOS device (
Bluetooth
model)
In
Bluetooth
model, select [
Bluetooth
Setup] and then select [Auto Re-Connect iOS], you can select whether to
enable or disable auto reconnection to iOS devices.
Bluetooth
Security Settings (
Bluetooth
model)
For
Bluetooth
models, select [
Bluetooth
Setup], and then select [Security], and you can change the
Bluetooth
security settings.
Pairing method when the security is set to Middle/High (from the printer)
When the security is set to Middle/High and the printer is ready to be paired, perform the following procedure.
1
Load paper in the printer, and then turn it on.
2
Open the roll paper cover, hold down the FEED button (two seconds), and then close
the roll paper cover.
3
A status sheet is printed, and the
Bluetooth
LED flashes a pattern indicating that pair-
ing is now possible.
•
For details on the auto re-connect function, see
"Auto Reconnect Feature" on page 109
.
•
You can change the settings with TM-m30II Utility and TM Utility for iOS.
When the security settings are changed from "Middle" or "Low" to "High", or vice versa, the link key
(pairing information) is deleted. If the printer is already paired with a terminal, unpair them and then
pair again.
You can change the settings with TM-m30II Utility and TM Utility for iOS/Android.
Security
Pairing Mode
Pairing Method
Low
Pairing is always possible
Just Works
Middle
(initial setting)
Pairing is possible for one minute after turning the printer on
or after printing the status sheet
Just Works
High
Pairing is possible for one minute after printing the status
sheet
Numeric Comparison/Passkey Entry
•
Make sure no errors have occurred and that the printer is not off-line.
•
You cannot pair the printer while the network is starting up immediately after the power is turned
on.
•
Pairing is possible for one minute after printing the status sheet.
•
You can enable pairing also by printing the status sheet by pressing the status sheet button.