Epson r-d1 User Manual - Page 36

Numbering Your Photos Sequentially, Calibrating the Needles on the Status Gauge

Get Epson r-d1 - Rangefinder Digital Camera PDF manuals and user guides View all Epson r-d1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

7. Focus on the subject again and press the shutter button down. Note: For more information, see the documentation for your flash. Numbering Your Photos Sequentially You can number your photos in sequence across different memory cards. 1. Use the JOG dial to select Sequential Numbering in the Basic Setup menu, and press the ENTER button. For details on using the menu, see "Basic Setup menu" on page 42. The Sequential Numbering screen is displayed. On (default) Off Numbering continues even when the memory card is replaced. Number is reset to 1 when the memory card is replaced. 2. Use the JOG dial to highlight On or Off, and press the ENTER button. The new setting is saved and the screen returns to the Basic Setup menu. Calibrating the Needles on the Status Gauge You can check the number of remaining photos, photo quality, remaining battery power, and white balance using the status gauge on the top of the camera. There are 4 needles on the gauge. If any of these needles becomes inaccurate, follow the steps below to adjust it. 1. Use the JOG dial to select Calibrate Needles in the Camera Settings menu, and press the ENTER button. The Needle Calibration screen is displayed. For details on using the menu, see "Camera Settings menu" on page 41. 31 Taking Pictures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
31
Taking Pictures
7.
Focus on the subject again and press the shutter button down.
Note:
For more information, see the documentation for your flash.
Numbering Your Photos Sequentially
You can number your photos in sequence across different memory
cards.
1.
Use the JOG dial to select
Sequential Numbering
in the Basic
Setup menu, and press the
ENTER
button. For details on using the
menu, see “Basic Setup menu” on page 42.
The Sequential Numbering screen is displayed.
2.
Use the JOG dial to highlight
On
or
Off
, and press the
ENTER
button. The new setting is saved and the screen returns to the Basic
Setup menu.
Calibrating the Needles on the Status
Gauge
You can check the number of remaining photos, photo quality,
remaining battery power, and white balance using the status gauge on
the top of the camera. There are 4 needles on the gauge. If any of these
needles becomes inaccurate, follow the steps below to adjust it.
1.
Use the JOG dial to select
Calibrate Needles
in the Camera
Settings menu, and press the
ENTER
button. The Needle Calibration
screen is displayed. For details on using the menu, see “Camera
Settings menu” on page 41.
On (default)
Numbering continues even when the
memory card is replaced.
Off
Number is reset to 1 when the memory
card is replaced.