Fluke 225C User Manual - Page 152

Modbus IEA-232/RS-232., Is in use in Process Industry, Building and Factory

Get Fluke 225C PDF manuals and user guides View all Fluke 225C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 152 highlights

Modbus IEA-232/RS-232. Is in use in Process Industry, Building and Factory Automation. Modbus RS-232 is used for point-to-point communication. System layout is shown in the figure below. Continuous data traffic is not ensured. CONTROLLER TxD RxD GND DEVICE UNDER CONTROL Modbus IEA-232/-RS-232 To check this type of bus, ScopeMeter Channel A is on and DC coupled. The recommended probe is the Fluke 10:1 probe. Connect the probe as shown below. TxD or RxD GND In case there are handshake lines, they can be measured as well as far as V-Levels are concerned. A Appendices Bushealth Measurements Modbus IEA-485/RS-485. Is in use in Process Industry, Building and Factory Automation. Modbus System layout is shown in the figure below. Continuous data traffic is not ensured. CONTROLLER DATA + DATA GND DEVICE 1 DEVICE 2 Modbus IEA-485/-RS-485 To check this type of bus, ScopeMeter Channel A and B are on and DC coupled. The recommended probes are Fluke 10:1 probes. Connect the probes as shown below. DATA + DATA DATA GND A-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
Appendices
Bushealth Measurements
A
A-5
Modbus IEA-232/RS-232.
Is in use in Process Industry, Building and Factory
Automation. Modbus RS-232 is used for point-to-point
communication. System layout is shown in the figure
below. Continuous data traffic is not ensured.
CONTROLLER
DEVICE UNDER
CONTROL
TxD
RxD
GND
Modbus IEA-232/-RS-232
To check this type of bus, ScopeMeter Channel A is on
and DC coupled. The recommended probe is the Fluke
10:1 probe. Connect the probe as shown below.
TxD or RxD
GND
In case there are handshake lines, they can be measured
as well as far as V-Levels are concerned.
Modbus IEA-485/RS-485.
Is in use in Process Industry, Building and Factory
Automation. Modbus System layout is shown in the figure
below. Continuous data traffic is not ensured.
CONTROLLER
DEVICE 1
DEVICE 2
DATA +
DATA -
GND
Modbus IEA-485/-RS-485
To check this type of bus, ScopeMeter Channel A and B
are on and DC coupled. The recommended probes are
Fluke 10:1 probes.
Connect the probes as shown below.
DATA +
DATA -
DATA GND