Fluke 225C User Manual - Page 153

Foundation Fieldbus H1 31.25 kBits/s., To check Foundation Fieldbus, ScopeMeter Channel A is - color scopemeter

Get Fluke 225C PDF manuals and user guides View all Fluke 225C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 153 highlights

Fluke 19xC-2x5C Users Manual Foundation Fieldbus H1 31.25 kBits/s. Is used to control 'field equipment' such as sensors, actuators, valves, and I/O devices via a two-wire connection. The system allows two-way communication between controller and the devices. Data traffic is continuous. The wires are marked + and - and carry a DC supply of about 24 Vdc with superimposed data of about 800 mVpp. The figure below shows the bus structure. To check Foundation Fieldbus, ScopeMeter Channel A is on and alternately AC coupled for data or DC coupled to test 24 Vdc. The recommended probe is the Fluke 10:1 probe. Connect the probe as shown below. DATA + DATA - Suitable measuring spots are the screw terminals that are present in a system's junction boxes. If preferred, you can use the TP88 Back Probe Pins (optional) to probe these terminals at the wire entry point. Commonly used wire colors are orange for + and blue for -. Probe A GND A A-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
Fluke 19xC-2x5C
Users Manual
A-6
Foundation Fieldbus H1 31.25 kBits/s.
Is used to control ‘field equipment’ such as sensors,
actuators, valves, and I/O devices via a two-wire
connection. The system allows two-way communication
between controller and the devices. Data traffic is
continuous. The wires are marked + and – and carry a
DC supply of about 24 Vdc with superimposed data of
about 800 mVpp. The figure below shows the bus
structure.
To check Foundation Fieldbus, ScopeMeter Channel A is
on and alternately AC coupled for data or DC coupled to
test 24 Vdc. The recommended probe is the Fluke 10:1
probe.
Connect the probe as shown below.
DATA +
DATA -
Suitable measuring spots are the screw terminals that are
present in a system’s junction boxes. If preferred, you can
use the TP88 Back Probe Pins (optional) to probe these
terminals at the wire entry point. Commonly used wire
colors are orange for + and blue for –.
Probe A
GND A