Fujitsu 6010N Getting Started Guide - Page 5

Do not touch the inside of the scanner unless necessary. Do not take apart or modify the scanner. The inside of the scanner contains highvoltage components. Touching these components might cause electric shock or fire. Do not use the scanner if you smell a strange odor. If you detect heat coming from the device or detect other problems such as smoke, strange smells or noises, immediately turn off the scanner and then disconnect its power plug. Make sure that any smoke coming from it has stopped, before contacting your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider. Do not use aerosol sprays near the scanner. Do not use any aerosol sprays or alcohol based sprays to clean the scanner. Dust blown up by strong air from the spray may enter the inside of the scanner. This may cause the scanner to fail or malfunction. Sparks, caused by static electricity, generated when blowing off dust and dirt from the outside of the scanner may cause a fire. Do not place the scanner within the reach of small children. To avoid injuries, do not place the scanner in an area where small children may be able to reach. Do not touch the heated section for a long time. Do not touch the heated section such as the bottom of the scanner for a long time. Doing so may cause a low-temperature burn on your skin. Do not cover the scanner with something during its operation. Do not use the scanner while covered with a blanket, etc. Doing so may raise the temperature inside and cause a fire. Do not use the scanner where it gets wet. Do not use the scanner at a place such as a bathroom, shower room, or swimming pool where it may easily get wet. Doing so might cause electric shock or fire. CAUTION Do not install the scanner on unstable surfaces. Make sure that the scanner is installed on a flat, level surface and that none of its parts extend beyond the surface top, such as a desk or table. Do not install the scanner on unstable surfaces. Install the scanner on a level surface that is free of vibration to prevent it from falling. Install the scanner on a strong surface that will support the weight of the scanner and other devices. Do not block the ventilation ports. Do not block the ventilation ports. Blocking the ventilation ports generates heat inside of scanner, which may result in fire or scanner failure. Do not place heavy objects or climb on top of the scanner. Do not place heavy objects on the scanner or use the scanner's surface top to perform other work. Improper installation might cause injuries and equipment failure. Firmly insert the power plug. Firmly insert the power plug as far it can go into the power outlet. vii fi-6010N Network Scanner Getting Started Avoid any contact when scanner is in use. Avoid touching any scanner mechanism during scanning since this may cause injuries. Handle documents carefully. When handling documents, be careful not to cut your fingers with them. Do not use the scanner immediately after moving it from a cold place into a warm room. Do not use the device immediately after moving it from a cold place into a warm room. Condensation may occur, which might lead to scanning errors. Let the device dry about one or two hours before you use it. Before moving the scanner, disconnect the power plug from the power outlet. Do not move the scanner with the power and interface cables connected as this can damage the cables, which can later cause fire, electric shock as well as injury. Before moving the scanner, be sure to disconnect the power plug from the power outlet, and all other data cables. Make sure that the floor is free of any obstructions. Do not make the scanner wet while carrying it outside. When carrying the scanner outside while it is raining or snowing, pay special attention so the scanner does not get wet. Do not place the scanner in areas, which are subject to high levels of shock or vibration. Do not place the scanner in areas, which are subject to high levels of shock or vibration. Doing so may cause the scanner to malfunction. Protect the scanner from static electricity. Install the scanner away from strong magnetic fields and other sources of electronic noise. Also, protect the scanner against any static electricity, which can cause the scanner to malfunction. Disconnect the power plug from the power outlet when the scanner is not used for a long period of time. When the scanner is not going to be used for a long period of time, be sure to disconnect the power plug from the power outlet for safety. Do not install the scanner in the direct sunlight. Do not install the scanner under direct sunlight or near heating apparatus. Doing so might cause excessive heat to build up inside the scanner, which can cause scanner trouble or even fire. Install the scanner in a well-ventilated location. viii