HP Dx5150 Troubleshooting Guide - Page 34

Integrated, Peripherals > South OnChip, IDE Device > OnChip IDE, Channel 0 - beep codes

Get HP Dx5150 - Compaq Business Desktop PDF manuals and user guides
UPC - 882780485433
View all HP Dx5150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Troubleshooting Without Diagnostics Solving Hard Drive Problems (Continued) Problem Cause Nonsystem disk/NTLDR missing message. (continued) Hard drive boot has been disabled in Computer Setup. Computer will not start. Bootable hard drive is not attached as first in a multi-hard drive configuration. Hard drive is damaged. Computer seems to be locked up. Program in use has stopped responding to commands. Solution Enter Computer Setup and enable the hard drive in Integrated Peripherals > South OnChip IDE Device > OnChip IDE Channel 0 or 1. Or Enter Computer Setup and enable the hard drive in Integrated Peripherals > South OnChip PCI Device > Onboard Chip SATA. If attempting to boot from an IDE hard drive, ensure it is attached as Primary Device 0. If attempting to boot from a SATA hard drive, ensure it is attached to SATA 0. Observe if the front panel Power LED is blinking RED and if any beeps are heard. See Appendix A, "POST Error Messages" to determine possible causes for the blinking red and beep codes. See the Worldwide Limited Warranty for terms and conditions. Attempt the normal Windows "Shut Down" procedure. If this fails, press the power button for four or more seconds to turn off the power. To restart the computer, press the power button again. 2-18 www.hp.com Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
2–18
www.hp.com
Troubleshooting Guide
Troubleshooting Without Diagnostics
Nonsystem disk/NTLDR
missing message.
(continued)
Hard drive boot has
been disabled in
Computer Setup.
Enter Computer Setup and enable
the hard drive in
Integrated
Peripherals > South OnChip
IDE Device > OnChip IDE
Channel 0
or
1
.
Or
Enter Computer Setup and enable
the hard drive in
Integrated
Peripherals > South OnChip
PCI Device > Onboard Chip
SATA
.
Bootable hard drive is
not attached as first in a
multi-hard drive
configuration.
If attempting to boot from an IDE
hard drive, ensure it is attached as
Primary Device 0. If attempting to
boot from a SATA hard drive,
ensure it is attached to SATA 0.
Computer will not start.
Hard drive is damaged.
Observe if the front panel Power
LED is blinking RED and if any
beeps are heard. See
Appendix A,
“POST Error Messages”
to
determine possible causes for the
blinking red and beep codes.
See the Worldwide Limited
Warranty for terms and conditions.
Computer seems to be
locked up.
Program in use has
stopped responding to
commands.
Attempt the normal Windows “Shut
Down” procedure. If this fails, press
the power button for four or more
seconds to turn off the power. To
restart the computer, press the
power button again.
Solving Hard Drive Problems
(Continued)
Problem
Cause
Solution