HP ENVY 14t-2000 HP ENVY 14 Notebook PC - Maintenance and Service Guide - Page 64

Solid-state drive connector board, Remove the Bluetooth module

Get HP ENVY 14t-2000 PDF manuals and user guides View all HP ENVY 14t-2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Remove the Bluetooth module: 1. Disconnect the Bluetooth module cable (1) from the solid-state drive connector board. 2. Release the grounding tape (2) that secures the Bluetooth module to the base enclosure. 3. Release the Bluetooth module cable (3) from the routing clips and channel built into the base enclosure. 4. Release the Bluetooth module (4) from the retention clip built into the base enclosure. 5. Remove the Bluetooth module and cable. Reverse this procedure to install the Bluetooth module and cable. Solid-state drive connector board Description For use only with computer models equipped with an mSATA solid-state drive For use only with computer models not equipped with an mSATA solid-state drive Spare part number 654171-001 661706-001 Before removing the solid-state drive connector board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 56 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
Remove the Bluetooth module:
1.
Disconnect the Bluetooth module cable
(1)
from the solid-state drive connector board.
2.
Release the grounding tape
(2)
that secures the Bluetooth module to the base enclosure.
3.
Release the Bluetooth module cable
(3)
from the routing clips and channel built into the
base enclosure.
4.
Release the Bluetooth module
(4)
from the retention clip built into the base enclosure.
5.
Remove the Bluetooth module and cable.
Reverse this procedure to install the Bluetooth module and cable.
Solid-state drive connector board
Description
Spare part number
For use only with computer models equipped with an mSATA solid-state drive
654171-001
For use only with computer models not equipped with an mSATA solid-state drive
661706-001
Before removing the solid-state drive connector board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
56
Chapter 4
Removal and replacement procedures