HP ENVY 15-bp100 Maintenance and Service Guide 1 - Page 36

Solid-state drive, Remove the solid-state drive

Get HP ENVY 15-bp100 PDF manuals and user guides View all HP ENVY 15-bp100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Solid-state drive Table 5-3 Solid-state drive description and spare part number information Description 512-GB, PCIe, NVMe, solid-state drive with TLC 256-GB, PCIe, NVMe, solid-state drive with TLC 256-GB, PCIe, NVMe, value solid-state drive 128-GB, M.2, SATA-3 solid-state drive with TLC Solid-state drive shield Spare part number L53563-001 L53565-001 L53564-001 L53872-001 L53543-001 Before removing the solid-state drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer. 4. Remove the bottom cover (see Bottom cover on page 25). 5. Remove the battery (see Battery on page 26). Remove the solid-state drive: 1. Remove the Phillips M2.0×2.3 broad head screw (1) that secures the solid-state drive to the system board. 2. Remove the solid-state drive (2) by pulling it away from the connector. NOTE: Solid-state drives are designed with notches to prevent incorrect insertion. Reverse this procedure to install the solid-state drive. 28 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Solid-state drive
Table 5-3
Solid-state drive description and spare part number information
Description
Spare part number
512-GB, PCIe, NVMe, solid-state drive with TLC
L53563-001
256-GB, PCIe, NVMe, solid-state drive with TLC
L53565-001
256-GB, PCIe, NVMe, value solid-state drive
L53564-001
128-GB, M.2, SATA-3 solid-state drive with TLC
L53872-001
Solid-state drive shield
L53543-001
Before removing the solid-state drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then
unplugging the AC adapter from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
25
).
5.
Remove the battery (see
Battery
on page
26
).
Remove the solid-state drive:
1.
Remove the Phillips M2.0×2.3 broad head screw
(1)
that secures the solid-state drive to the system board.
2.
Remove the solid-state drive
(2)
by pulling it away from the connector.
NOTE:
Solid-state drives are designed with notches to prevent incorrect insertion.
Reverse this procedure to install the solid-state drive.
28
Chapter 5
Removal and replacement procedures