HP Elite 7100 Maintenance & Service Guide: HP Elite 7100 Series Microtower - Page 65

Power Switch/LED Assembly

Get HP Elite 7100 - Microtower PC PDF manuals and user guides View all HP Elite 7100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Power Switch/LED Assembly The power switch/LED assembly is located on the top left corner of the computer. Its cable is routed on the side of the optical drive, meaning the you must remove the optical drive to remove the power switch/LED assembly. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 28). 2. Remove the access panel (Access Panel on page 29). 3. Lay the computer on its side with the front facing toward you. 4. Remove the front bezel (Front Bezel on page 30). 5. Remove the optical drive (Removing an Optical Drive on page 45). 6. Disconnect the braided cables from the black system board connector labeled JFP1. 7. Remove the cable from the clips in the optical drive cage. 8. Press the tab on the top of the switch holder (1) to disengage it from the chassis, lift the switch upward (2) to disengage the tab at the bottom of the switch from the chassis, and then pull the power switch away from the chassis while guiding the wires through the hole in the chassis. To install the power switch/LED assembly, reverse the removal procedures. Power Switch/LED Assembly 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
Power Switch/LED Assembly
The power switch/LED assembly is located on the top left corner of the computer. Its cable is routed
on the side of the optical drive, meaning the you must remove the optical drive to remove the power
switch/LED assembly.
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
28
).
2.
Remove the access panel (
Access Panel
on page
29
).
3.
Lay the computer on its side with the front facing toward you.
4.
Remove the front bezel (
Front Bezel
on page
30
).
5.
Remove the optical drive (
Removing an Optical Drive
on page
45
).
6.
Disconnect the braided cables from the black system board connector labeled JFP1.
7.
Remove the cable from the clips in the optical drive cage.
8.
Press the tab on the top of the switch holder
(1)
to disengage it from the chassis, lift the switch
upward
(2)
to disengage the tab at the bottom of the switch from the chassis, and then pull the
power switch away from the chassis while guiding the wires through the hole in the chassis.
To install the power switch/LED assembly, reverse the removal procedures.
Power Switch/LED Assembly
57