HP Evo D500 Hardware Reference Guide Compaq Evo Desktop Family Convertible Min - Page 46

Guidelines for Installing Ultra ATA Devices

Get HP Evo D500 - Convertible Minitower PDF manuals and user guides View all HP Evo D500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Hard Drive Installation Guidelines Guidelines for Installing Ultra ATA Devices When installing additional Ultra ATA drives, follow these guidelines: ■ If using multiple Ultra ATA devices, Compaq recommends that the devices be split between the primary and secondary Ultra ATA channels for optimum performance. Use an additional Ultra ATA cable to connect the additional device to the system board. ■ 80-conductor Ultra ATA cable: ❏ 18 inches maximum total length, 80-conductor cable with maximum spacing of 6 inches between Device 0 and Device 1. 80-Conductor Ultra ATA Cable 1 Device 0 (master drive) connector 2 Device 1 (slave drive) connector 3 System board connector ■ For optimal performance, connect hard drives to the primary controller. Connect expansion devices, such as ATA CD-ROM and DVD-ROM drives, tape drives, and diskette drives, to the secondary controller. ■ Install either a third-height or a half-height drive into a half-height bay. ■ Install guide screws to ensure that the drive lines up correctly in the drive cage. Compaq has provided extra guide screws installed in the front of the computer chassis behind the front bezel. Some options use M3 metric hardware. Compaq supplied metric screws are black. ■ If only one device is connected to a cable, that device must be attached to the end (Device 0) connector. B-2 Hardware Reference Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Hard Drive Installation Guidelines
Guidelines for Installing Ultra ATA Devices
When installing additional Ultra ATA drives, follow these
guidelines:
■
If using multiple Ultra ATA devices, Compaq recommends that
the devices be split between the primary and secondary Ultra
ATA channels for optimum performance. Use an additional
Ultra ATA cable to connect the additional device to the system
board.
■
80-conductor Ultra ATA cable:
18 inches maximum total length, 80-conductor cable with
maximum spacing of 6 inches between Device 0 and Device 1.
80-Conductor Ultra ATA Cable
1
Device 0 (master drive) connector
2
Device 1 (slave drive) connector
3
System board connector
■
For optimal performance, connect hard drives to the primary
controller. Connect expansion devices, such as ATA CD-ROM
and DVD-ROM drives, tape drives, and diskette drives, to the
secondary controller.
■
Install either a third-height or a half-height drive into a half-height
bay.
■
Install guide screws to ensure that the drive lines up correctly in
the drive cage. Compaq has provided extra guide screws installed
in the front of the computer chassis behind the front bezel. Some
options use M3 metric hardware. Compaq supplied metric screws
are black.
■
If only one device is connected to a cable, that device must be
attached to the end (Device 0) connector.
B-2
Hardware Reference Guide